Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
2-1/8" x 1-1/8" Rectangle. Waterproof, LED trailer light serves as either a side marker light or clearance light when properly mounted. Durable polycarbonate lens and housing. Stud mount to trailer. Two wire design. P2 rated.
Features:
Specs:
The waterproof construction of this light makes it ideal for use on trailers that may be submerged, like a boat trailer. The housing and lens are sonically sealed together to create a single unit, which means that water will not get into the light and damage the diodes or circuit board.
A P2-rated light produces a 45-degree angle of light to either side of its centerline for a total of 90 degrees of coverage. This beam pattern can be seen straight on, but it cannot be seen clearly from the side. So this type of light can be used as either a side marker light or a clearance light, but it cannot function as both. If you need both functions, then you must install 2 separate lights on your trailer - one as a front or rear clearance light and one as a side marker light.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hi there, I'm Michael with etrailer.com, today we're gonna take a quick look at this Optronics submersible LED trailer clearance or side marker light. This LED trailer light is going to function as either a clearance light or a side marker light depending on how you have it mounted. It is P2 rated which means it's going to produce a 45 degree angle. So the light can be seen on either side of its center line for a total of 90 degrees but can't be seen as clearly from the side because it's not a full 180 degrees of light being there. So you will be able to either use it as a clearance light or a side marker light depending on how you have it installed. This is sonically sealed, so it's going to be waterproof.
Great application would be for your boat trailers or something that you're gonna be putting into water frequently, waterproof polycarbonate housing and lens unit is going to keep it nice and water tight so that you don't have to worry about water getting in there and causing any issues. This does have a red lens over those three light LEDs. If you're not familiar, LEDs are a really nice replacement for your traditional incandescent lights. There are a lot more efficient, so it's gonna provide brighter light with less power output. The bulbs are also a lot more durable, so you're not gonna have to replace them nearly as frequently because they don't have those brittle filaments on the inside, so they last about 50 times longer than your traditional incandescent lights.
This one actually has a lifetime warranty on those LEDs, so you can trust, it's gonna last for a nice long time for you. This does have a two wire design, so you've got your lead and your ground that you'll be able to hook up to your wiring system. This is gonna be compatible with your 12 volt DC systems, it's only gonna draw about a 0.051 amps on your 12 volt system. This does also have the stud Mount that's going to connect it to your trailer the included stud and stainless steel base. And as far as our dimensions go, we're looking at right two and one eighth of an inch long by one and one eighth of an inch wide, and if we measure right where that base is, we are gonna have right about one and one eighth of an inch deep as well.
So if you are looking for a red side marker or clearance light for your boat trailer or any of your other aquatic trailers, this is gonna be a really great option for you to provide that light for you. That's going to complete our look for today, again, I'm Michael with etrailer.com thanks for watching..
Average Customer Rating: 4.6 out of 5 stars (13 Customer Reviews)
2-1/8" x 1-1/8" Rectangle. Waterproof, LED trailer light serves as either a side marker light or clearance light when properly mounted. Durable polycarbonate lens and housing. Stud mount to trailer. Two wire design. P2 rated.Horrible. I had to return as 99/100 lights have a ground without a secondary wire and they have a steel back that would rust out so quick. I sent these back to etrailer, but I still have not received a credit for them. They were sent back with everything within etrailer requirements for return. Where is my credit even after being authorized by etrailer staff? Be careful with etrailer if you need to return something. They do not quickly return your money.
Quick shipping and great selection.
Brian
8/9/2023
Still working well.
Product appears to be extremely well-ma de.
THEY WORKED EXCELLENT ON MY JOHN DEERE TRACTOR. NICE & BRIGHT. WILL BUY AGAIN.THANK YOU !
Great price easy ordering shipping was quick video on installing exceptional
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Jenny N.
2/20/2024
My apologies that the credit has not been applied for you. Customer Service will reach out and remedy this ASAP. As for the light we do have a similar light that does only have one wire as part # MCL95RB. It grounds through the hardware that mounts it to the trailer frame.