4" x 7/8" Rectangle. Waterproof, LED trailer light serves as either a clearance or side marker light. Durable polycarbonate housing and lens. Surface mount to trailer with bracket (sold separately). 2-Wire design. P2 rated.
Features:
Specs:
The waterproof construction of this light makes it ideal for use on trailers that may be submerged, like a boat trailer. The housing and lens are sonically sealed together to create a single unit, which means that water will not get into the light and damage the diodes or circuit board.
A P2-rated light produces a 45-degree angle of light to either side of its centerline for a total of 90 degrees of coverage. This beam pattern can be seen straight on, but it cannot be seen clearly from the side. So this type of light can be used as either a side marker light or a clearance light, but it cannot function as both. If you need both functions, then you must install 2 separate lights on your trailer - one as a front or rear clearance light and one as a side marker light.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today, we're going to take a look at the Optronics submersible red thin line LED trailer clearance or side marker light. Now this is a rectangular LED trailer light. It functions as a clearance light or a side marker light when it's properly mounted. It is a thin line series has a nice low profile so that the light can fit into tight spaces. It is sonically sealed, waterproof housing and lens unit is submersible, and it uses a durable polycarbonate housing and lens. The red lens over white LEDs.
These LEDs will make great replacements for incandescent lights because they'll last 50 times longer and they're more efficient. They'll provide brighter light with less power output, and of course, no bulbs to replace or brittle filaments to break.Now, this light is compatible with 12-volt DC electrical systems. It is a surface-mount design. It mounts to the trailer using a mounting bracket, which we do sell separately. It's part number BK66DB.
This is a two-wire design and includes the power lead and the ground wires. You can see they have the bullet connectors on each end, and this is non-polarized, even though the wires are white and black it's non-polarized so you could hook it up to either positive or negative.I am going to hook this up at the end of the video just to show you how bright it is. This light is DOT, Department of Transportation, compliant and it is P2 rated. It does use six LEDs. The power draw at 12.8 volts is 0.057 amps, and they do offer a lifetime warranty on the LEDs.I first want to give you some measurements.
If we measure the overall length of this light, it's going to be right at four inches long. The height of it is right at seven-eighths of an inch tall, and the depth from the light is one and three- sixteenths of an inch deep. Now the mounting holes, there's two of them here, and center to center measurement is three inches. You can see the lights when you do surface mount this, they have cutouts there that the wires will go on there so it'll give you a surface-mount design. There's two cutouts for the wires.What I'm going to do now is we're going to hook up the 12-volt power so you can see I'm going to take the white wire and hook it to the black, and the black to the red.
When we'll go ahead and turn on our power and you can see there's your bright light. We'll go ahead and turn off the overhead and you can see there's six LEDs in there that light up, give you a nice clearance light or side marker light.Then what I'm going to do is just show you I'm going to reverse it. We'll put the red on the white and the black on the black, and you can see it still lights up. It doesn't matter, it's non-polarized so it doesn't matter which positive or negative is hooked up. But that should do it for the review on the Optronics submersible red thin line LED trailer clearance or side marker light..
Average Customer Rating: 4.9 out of 5 stars (14 Customer Reviews)
4" x 7/8" Rectangle. Waterproof, LED trailer light serves as either a clearance or side marker light. Durable polycarbonate housing and lens. Surface mount to trailer with bracket (sold separately). 2-Wire design. P2 rated.The lights were the exact replacement for what we needed and the shipping was super fast which was great to get the bus through state inspection
Excellent, works great got it sooner than I supposed to
Parts worked great. Good price, on-time delivery.
After 2 years these lights are still super bright and durable.
I trim trees regularly driving tight tree lined streets. The lights are not bullet proof but close to. I love them
E-trailer is a great co, and I will go to them again when I need someting.
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.