To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
This fully welded trailer hitch receiver bolts onto your Toyota Sienna's frame with no welding required. Matte black, powder coated steel is durable and corrosion resistant and creates a rugged look.
Features:
Specs:
The sturdy steel construction is protected with a matte black finish for added durability. This unique powder coating gives etrailer hitches a carbide-like appearance and a rugged look that sets them apart from traditional glossy hitches. In addition to being rust and corrosion resistant, the tough matte coating hides dirt, scuffs, and dings better than a glossy finish.
At etrailer we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
Tech Tip
No drilling required for installation , Underbody panel(s) and/or fascia must be temporarily loosened or removed. Trimming may be needed to reattach panel or fascia. , Exhaust must be temporarily lowered for installation , Underbody trimming required (not fascia)
Complete Towing Package for 2012 Toyota Sienna
2012 Toyota Sienna Owners Who Purchased This Trailer Hitch Also Bought...
Popular Sienna Trailer Hitch Accessories
Average Customer Rating: 4.8 out of 5 stars (742 Customer Reviews)
This fully welded trailer hitch receiver bolts onto your vehicle's frame with no welding required. Matte black, powder coated steel is durable and corrosion resistant and creates a rugged look.Looks great! It's so new I haven't put it to a test yet. It will be used primarily for transporting electric bikes. One bike is a fat-tire bike. Viewing your reviews of best bike carriers. The trailer hitch receiver was installed professionally.
This Hitch receiver was easy to install on our 2006 Toyota Sienna, the one bolt located under the muffler needs a little extra time during the install, but it's straightforward. We have 5 place bike rack that installs on the rack and it's been rock-stable, even over 500 mile trips. My only complaint is with the ground clearance (it's a Toyota issue) with the receiver installed you lose a lot on the departure angle, so be prepared to scrape a few times and watch for speed bumps, pulling out of driveways, etc. e-trailer's product though is top notch, well-built and has been great over our year of ownership.
It was easy to install and has held up well with no problems. My trailer loaded is around 600 lbs and I’ve pulled it several 1000 miles with the hitch. I would definitely buy another one if needed.
Awesome hitch at a good price! Easy installation, great instructions and hardware. Fits tight, looks OEM! Thanks for great product!
It works fine, no problems with the boat trailer.
Fits perfect. Great video instructions. Quick shipping.
The trailer box arrived damaged but the trailer hitch receiver looked fine. When installing the hitch, it would not fit with several attempts. I contacted etrailer for support and received an email instruction to realign the hitch. After realignment of hitch, it fit just fine and the hitch looked awesome. Thanks etrailer for the quick response on the solution. The hitch was mis-aligned due to shipping. The hitch is very strong with an awesome price from etrailer. I have purchased another hitch from etrailer and it was also great quality. Thanks again (Quinn F. at etrailer) for providing quick support to solve my problem. Great value with free shipping. (2011 Toyota Sienna)
Hitch receiver looks sharp, was easy to install, and was a very reasonable price. I am very happy with my choice.
My husband and I were able to install it with little difficulty. Because of the weight of the hitch it took a few different tries to screw it into place. I would suggest using tire jacks to hold it in place while you get it bolted. We’ve had it for over a year and it’s been perfect.
Erin
7/16/2023
Perfectly!
I am fairly mechanical and can savvy instructions well enough, so I read over them a few times prior to installing. I installed this by myself, with no other hands helping me - if this is you, READ ON!
I jacked up the back of the van and used two jack stands so that I could actually breathe. That made all the difference (don’t forget your parking brake!).
There is a piece of the body that is plastic - you will have to remove this and cut a hole so that the hitch mount will actuallly fit. I took the time to do this and it made the install so much easier. I had a set of tin snips and they worked great for this. Although, pay attention to the different fittings that hold this piece of plastic in place. There are three different kinds: Phillips screw, LARGE Phillips screws, and little pop out fittings. So you take this thing off and put it back on before you ever get to any of the actual installation.
There are covers for the welded frame nuts on the Sienna. They are basically stickers. I jabbed a hole in them with a screw driver and pulled them apart to expose the nut. Since they are covered, mine were clean as a whistle and I didn’t have to blow them out or use a wire brush.
Instructions for this item are great, measurements for the piece you HAVE to cut are totally correct, except I would make them bigger so you can fit your ratchet extension in.
I DID NOT lower the exhaust. I actually used it as a prop on the passenger side as I finger tightened a bolt on the driver side (remember I did this by myself). Then I finger tightened a couple of bolts on the exhaust (passenger) side. After finger tightening all of the bolts, I took my time tightening each bolt twice. I don’t have a torque wrench, so I don’t know how tight they are. I tend to have a tight grip, so I am sure they are fine, but I’ll check them again in a week or so. NOTE, tightening the bolts on the exhaust side requires you to pull the exhaust to the side so you can get your ratchet in position. I used the ratchet extension as leverage and this helped. If you could lower the exhaust, it might be easier, but that seemed like a needless pain.
We are taking our first trip with it this weekend - carrying three mountain bikes. I’ll check the bolts when we get there and when we get back.
All in all, this hitch mount is a beast. Very heavy duty, and will handle anything our Vinnie-Man will dish out :)
Mike L.
2/28/2019
Thanks for the review! I highly recommend making sure those bolts are correctly torqued. Most national chain auto parts stores will loan tools for free if you leave a deposit, thatd be a great way to borrow a torque wrench.
Installed easily and has pulled our 20’ sailboat without mishap.
First-class build quality. The welds are solid and the cuts are crisp.
The only reason for 4/5 stars is that the instructions need significant work. The photos are small and dark, the text is terse, and the difficulty is significantly under-rated.
I am a skilled handyman with all required tools. This project took me about two and a half hours, and a significant part of that time was spent scrutinizing the sparse instructions.
The price was also reasonable. I'm a repeat customer, and I would definitely buy again.
Four images attached. Use as you like.
xxx07.jpg: Splash guard cutout around left side
xxx32.jpg: Close up of long transverse cut across splash guard for guards that have long ridge that interferes with hitch.
xxx02.jpg: Close up of *threaded* splash guard holder. Indent is very large phillips-like cross. Size is roughly that of a quarter.
xxx41.jpg: Close up of snap connector. Inner white button pops out with screwdriver.
This is awesome hitch receiver easy to install.and one thing I like to this item
my after market rear lip has no modified or cut.
Hitch Receiver works as it should and it's not too difficult to install.
Product is reasonably well made. Accessories are poorly made and packaged. The paper box came in almost completely dismantled and both mounting screws and pin alignment stop were missing, and the receiver was lightly scratched. However the customer service did immediately shipped out the replacement mounting accessories and alignment stop within days, and credited me $xx, for touchup paint from local [hardware store]. The touchup paint was a nice touchup. Thanks!
Easy to install. Works great.
I purchased 2 trailer hitches (one for a 2014 Toyota Sienna and one for a Hyundai Tuscan) for our Thule Bicycle Rack and both hitches are working great! Thanks!
The installation video was wrong you also have to cut the plastic for the center of the hitch on my 2020 sienna limited edition. Very frustrating hope this helps the next person that install one.
This hitch, as with prior etrailer hitches was easy to install with the how-to videos. I keep coming back to etrailer.
Easy to install and works like a charm
Very easy install. Took 2 of us about 45 minutes from start to finish. Flanges on hitch where bent a little bit from shipping but we were able to straighten them out.
Hitch scrapes sometimes when i leave my driveway or on certain Speed Bumps but overall a great well built Hitch.
Love the product, very well made. Very beefy and sturdy, it’s heavy and solid. It was very easy to install on my dorkmobile and the hardware provided is all that you need. I would recommend this thing to everyone that has a 05 Toyota Sienna and wants a hitch on it!
This thing works great and continues to work for me. Although I just traded that vehicle for another Toyota Sienna and I will soon be purchasing another one of these.
I am very impressed! The company, product, pricing and my self "DIY", installation was all very good and I would do it again if I ever had the need, Thanks E-Trailer!
Installed fairly easily. Looks good. I did have to trim the under carriage cover around the 2” opening but otherwise it was no big deal. I installed this on a 2017 Sienna Limited.
Do you have a question about this Trailer Hitch?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Aaron
1/4/2024
Another year later and the hitch receiver is flawless. VERY sturdy no rust and no issues.