MB Sturgis Propane Hose - 3/8" Male NPT x 3/8" Female Flare Swivel - 12'

See what our Experts say about this MB Sturgis Propane Fittings

• MB Sturgis High Pressure Propane Hose - 3/8" MPT x 3/8" Female Flare Swivel
  We have MB Sturgis High Pressure Propane Hose - 3/8" MPT x 3/8" Female Flare Swivel in varying lengths but currently 12' is the longest, # 100040-144-MBS.
  view full answer...
• Hoses and Regulators Needed to Add Dual Tank Propane Setup to Trailer
  I attached a picture that shows what the typical dual tank setup looks like with the accessories needed labeled. First thing you need is pig tails to go from the tanks to the regulator like the part # 100473-12. Then for a dual tank regulator with automatic changeover we have the part # 37207-30395 that each of the pigtails would connect to. Then for a 12 foot long extension hose that would plug into outlet of the regulator you'd want the part # 100040-144-MBS. From there you'd connect...
  view full answer...
  
• Correct 12" Propane Hose for Connector with Almost 3/4" Thread Diameter
  Thanks for all of the info! It sounds like you're needing the 12' MB Sturgis Propane Adapter Hose # 100040-144-MBS which has 3/8" Male NPT x 3/8" Female Flare Swivel ends. Propane fittings can be confusing because they go by the inner diameter of the hose as opposed to the diameter of the fittings directly. The 3/8" NPT fittings measure 0.675" for the thread diameter (see attached) which sounds like what you've been measuring. Hope this helps make it less confusing! I'm attaching a link...
  view full answer...
  
• Regulator and Hoses Required for a Dyna-Glo 20000 BTU Wall Heater
  According to the user manual for Dyna-Glo wall heaters, they require a propane gas line pressure of 11in WC (water column). You will need a 2-stage regulator to reach this pressure level like part # 37207-30375. This regulator comes with the POL fitting that will thread directly into the valve on your tank and you will just need a supply hose to go from the regulator to the heater. We have these hoses available in the following lengths: 12 ft - # 100040-144-MBS 6 ft - # 100040-72-MBS 5...
  view full answer...
• Champion Generator Replacement Propane Hose Availability
  We have the MG Sturgis Propane Hose part # 100040-144-MBS which matches what you are looking for. It has the correct fitting size and is 12 feet in length.
  view full answer...
• Do I Need a Separate Low Pressure Regulator for a Camco Olympian Wave Heater
  Yes, you will need to use a low pressure regulator with the Camco Olympian Wave 8 part # CAM57351 but that is what the Camco Horizontal 2-Stage Propane Regulator part # CAM59323 is. Therefore, if you have the heater tied in after the above regulator then you won't have any issues. In order to attach the Camco Olympian Wave 8 to the manifold on your trailer you are most likely going to need the MB Sturgis High Pressure Propane Hose part # 100383-36-MBS for 3' long, part # 100040-72-MBS...
  view full answer...
• Recommendations For Van Build Propane System
  You're going to need a regulator if you don't have one hooked up already so I would run a line from your tank to a regulator like Item # CAM59323 and then you can run a line like Item # 100040-144-MBS up into your van and up to the appliances. Depending on the type of connection you have up inside the van for the appliances you could choose a different hose to match that connection. You could definitely bend some conduit and run the hose through it and bracket it onto the underside of the...
  view full answer...
• Can Flexible Propane Hose be Used to Relocate Propane Tank
  Yes you could use flexible propane hose like the part # 100040-144-MBS which has 3/8 inch fittings and is 12 feet long to move your propane tanks to a different location.
  view full answer...
• What Type of Connector is on Onan 6500 LP Generator
  That looks like a male NPT fitting like what the Camco Propane Extension Hose part # CAM59883 has and would connect to. This hose is 5 foot long.
  view full answer...
  
• Hose Kit to Go From RV Propane Tank to Propane Regulator
  We have hoses like what you are looking for such as the part # 100040-144-MBS which is a 12 foot hose designed to go from a propane regulator to your trailer's gas piping system. I attached a page that has all of the sizes we carry too.
  view full answer...
• Solution for Needing 50 Foot 3/8 inch Fitting Propane Hose Rated for 350 psi
  The closest thing we offer is the # 100040-144-MBS which is rated for 350 psi and has 3/8 inch NPT and 3/8 female flare fittings but is only 12 feet long. You'd need 5 of these to total 50 feet.
  view full answer...
• Parts Needed For Connecting Two 100LB Propane Tanks To a Furnace
  You will most likely need the MB Sturgis High Capacity Two-Stage Auto Changeover Regulator # 888001-MBS for going to your furnace. Be sure to verify with the furnace manufacturer that a 11" WC regulator that delivers 450,000 Btu P/HR is compatible with that furnace. With this auto changeover regulator it will draw propane from one tank until empty and then switch over to the 2nd tank automatically so you won't have to change anything to the 2nd tank. To connect your 100lb propane tanks...
  view full answer...
• Replacement Propane Trunk Hose from Regulator to Trailer
  It's hard to tell from the pictures what size fittings are being used but what you need is a trunk hose from your regulator to the trailer. Once you know the size of each fitting it shouldn't be difficult to find a hose. It looks to me likes it's probably a 3/8 inch for both of them which means you can use part # 100040-48-MBS for a 4 foot, part # 100040-72-MBS for a 6 foot, or part # 100040-144-MBS for a 12 foot. If it turns out the female end (regulator side) is 1/2 inch and the male...
  view full answer...
  
• Needing 1/4 Inch Male NPT to Quick Disconnect Propane Extension Hose
  We've got exactly what you're needing, part # 37207-31135 is a 10 foot hose featuring a male quick disconnect on one end and a 1/4 inch male NPT on the other.
  view full answer...
• Propane Hose for Cummins Onan RV Generator
  Thank you so much for the info and the pictures! According to my research it looks like your Cummins Onan RV Generator uses a 3/8" NPT Female fitting so you'll need a hose like part # 100040-144-MBS. I have attached a link to all of our hose selections that have the 3/8" male and female ends that you can filter through. I'm not quite sure what end you'll need to connect this to a regulator/propane tank as it looks like the male end goes into your generator when it is normally supposed...
  view full answer...
  
• How to Connect Two 40 lb. Propane Tanks Together
  Yes, you will want the same equipment to connect (2) 40 lb. propane tanks together as long as your 40 pound tanks feature a standard ACME or P.O.L. fitting (which most do). You will want an (1) Automatic Changeover RV LP Gas Regulator # 37207-30395. Then you will also need (2, one for each tank) MB Sturgis Propane Pigtail # 100833-12 and (2, one for each tank) Camco Propane Cylinder Gas Gauge and Leak Detector # CAM59023. You would also need a hose coming from the regulator to the your...
  view full answer...
• How to Hook a Converted Propane Clothes Dryer Up To a 100 Lb Propane Tank
  The MB Sturgis Vertical 2-Stage Propane Regulator part # 108220 will work with your 100 lb propane tank if mounted straight up and down so that the vent is facing the ground (see photo). In order to attach this regulator to the tank you will need to use the MB Sturgis Hose Assembly part # 100202. In order to recommend the correct fittings and hose to attach the outlet of the regulator to your clothes dryer I would need to know what fitting you have on your clothes dryer. If you do not...
  view full answer...
  
• Propane Supply Fitting For Furrion 2-in-1 Range Oven FR57KR
  I checked with Furrion and they do not have a recommended propane gas line size for the Furrion 2-in-1 Range Oven with Glass Cover - 17" Tall - Stainless Steel # FR57KR. It requires a hose/line with a 3/8" Female Flare connection, with the right one depending on the length depending on the length you need and what you are connecting to. For example the MB Sturgis Propane Adapter Hose # 100040-144-MBS is 12 feet long and has a 3/8" Male NPT connection on one end and 3/8" Female Flare on...
  view full answer...
• Recommended Temporary Propane Hose From Tank to House
  In order to choose the correct propane hose you will need to know what size fittings you have on either end of the accessories that the line will be hooked up to. If you are referring to a dual stage propane regulator such as the MB Sturgis Horizontal 2-Stage Propane Regulator part # 108221 then these usually have a 3/8" NPT outlet. If that is the case then the MB Sturgis High Pressure Propane Hose part # 100040-144-MBS is the longest we have at 12' but you could certainly combine multiple...
  view full answer...
• Are Fittings on MB Sturgis High Pressure Propane Hose a Left Hand Thread
  The MB Sturgis hose, part # 100040-144-MBS, is a standard right hand thread. The only standard propane fittings that are left hand thread are POL fittings, like part # 204128-MBS.
  view full answer...
• Recommended Propane Regulator and 8 to 10 Foot Hose to Supply a Food Trailer
  To supply your food trailer from your 100 pound tank you're going to need a pigtail, like part # 100473-20-MBS, that goes from the tank to a regulator. The regulator needs to be a 2-stage regulator like part # 108220. Then from the regulator use part # 100040-144-MBS. It's 12 feet long so more than what you need but we don't have an 8 to 10 foot hose that has a 3/8 male to connect to a regulator with a 3/8 female flare on the other end. The next shortest option we carry is 6 feet long,...
  view full answer...
• Size of Propane Hose to Go From Tank to Regulator on RV
  Most regulators like the part # CAM59005 have an inlet of 1/4 inch SAE and an outlet of 3/8 NPT. It would be out of the ordinary if your tank to regulator wasn't 1/4 inch SAE inverted flare. Part # CAM59053 has this style of fittings on both sides. Part # 100040-144-MBS has 3/8 inch on the other hand. Heres how you tell difference between 3/8 NPT and 1/4 NPT. The difference is the outside diameter. 1/4 inch is .540 outside diameter on the threads and 3/8 inch is .675 inch.
  view full answer...
• Parts Needed To Hook Duromax 13,000 Watt Dual Fuel Generator To Dual 100lb Tanks
  I took a look at your DuroMax 13,000 watt generator and it appears to have a 3/8" male flare on it for the propane line to hook up to which you'll want to confirm using the included help article. As long as that's the fitting you have you will need the following parts to hook up your generator to dual 100lb tanks: (2) pigtails # 100019-36 (1) regulator # 37207-30395 (1) supply hose # 100040-144-MBS You'll need to figure out your own mount to secure the regulator, but it'll automatically...
  view full answer...
• Parts Needed To Transition To A Two Propane Tank Setup On A Trailer
  We sure do! Starting with the base we have a mounting tray # 37230BL that you can attach to the tongue of your trailer to secure two 30lb tanks. Next you'll need a regulator like part # 888001-MBS, which also comes with a mounting bracket that you can attach to the post of the # 37230BL. To connect your tanks to your regulator you can use two pigtail hoses like # 100575-12-MBS. For the supply line from the regulator to the hardline system on your trailer you'll need to use a hose with...
  view full answer...

Do you have a question about this Propane Fitting?