T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector

See what our Experts say about this Tekonsha Custom Fit Vehicle Wiring

• What do You Recommend to Transport a 24 x 48 260 Pound Object on a Flat-Towed 2014 Grand Cherokee?
  The only option we currently have that will give you the 24 x 48 inches of space you need as well as the safety, I recommend the GearSpace 34 Enclosed Cargo Carrier for 2" Hitch - Slide Out item # HGK819 (dark grey) or item # HGK826 (light grey). With the GearSpace 34, it has internal dimensions of 63" long x 28" wide x 40" tall. Also, the GearSpace 34 has been constructed to withstand the added torque and force when mounted on a hitch receiver on a flat-towed vehicle. Almost all of our...
  view full answer...
• Troubleshooting Stoplight Circuit of 2011 Toyota Tacoma Trailer Wiring Not Functioning
  It does sound like the converter box has shorted out and you would need to replace it with the part # 118496 which is correct fit for your 2011 Toyota Tacoma. If the blinker circuits are still functioning on the trailer wiring but the brake light circuit is dead then that would indicate the circuit board isn't functioning properly and would need replaced.
  view full answer...
• Troubleshooting 2008 Chevy Silverado 2500 Where 12 Volt Circuit on 7-Way isn't Active
  There are a couple connections you need to make under the hood of your 2008 Chevy 2500HD to allow the 12 volt accessory circuit of your 7-way to activate. If you check out the help article I attached and then scroll down to the section titled "Finalizing Connections for the Brake Controller" you'll see the entire process outline.
  view full answer...
• Reason for Blown 12V Trailer Connector Fuse on 2014 Ram Truck
  Usually a blown fuse is caused by some kind of short from a damaged or exposed piece of wiring. If the 12V fuse on your truck is blown, I recommend tracing the wiring going to the 12V pin on your 7-Way (1 o'clock position) and checking for any exposed areas that might be making contact with bare metal or another wire. Also inspect the 7-Way itself for any debris or corrosion that might be built up behind the pin. I took a look at the online owner's manual for your 2014 Ram and it looks...
  view full answer...
• 12V Fuse Location for 2017 Ram 3500
  I took a look at the online owner's manual for your 2017 Ram 3500. It looks like the fuse related to the 12V pin at the 7-Way should be located at the F30 position inside the power distribution center (in the engine compartment). This will be a 30 amp pink fuse. You will just want to make sure this fuse is present and in good condition. Other fuses on your Ram related to towing are as follows: F28 - Trailer Tow Backup Lights - 20 Amp Blue F29 - Trailer Tow Parking Lights - 20 Amp Blue F53...
  view full answer...
• How to Add Second Wiring Harness to 2018 Toyota Tundra to Power Tailgate Light Bar
  If your 2018 Tundra has wiring that uses a round U.S. Car type connector (like the item shown in the linked photo) then you can easily piggyback a second wiring harness and have both remain active. Most tailgate light bars use a 4-pole flat connector so if this is what you have all you need is part # 118384 which will simply plug in between your 7-way socket and the U.S. Car connector that connects to the back of it. Please check out the linked install video. I strongly recommend using...
  view full answer...
  
• Hitch Recommendation For a 2010 Dodge Ram 2500 Mega Cab With a Factory Installed Hitch
  You might want to check the hitch on your 2010 Dodge Ram 2500, but it is usually welded on to the frame of your vehicle. It would be very difficult to remove. I would recommend the Curt Class V 2 Inch Hitch, part # C15409. This hitch has 17000 lbs towing weight capacity and 2550 lbs tongue weight capacity. If you will be towing with the Curt hitch you will also need the Draw-Tite Ball Mount, part # 40331, the part # PC3 Pin and Clip, and the hitch ball. Depending on the coupler size...
  view full answer...
• Can Rear Fascia Panel be Replaced After Installing Curt Trailer Hitch # 13424, 2011 Chevy Traverse
  You will notice in the instructions that I have linked for Curt Trailer Hitch, # 13424, that it states that the panel in question may be reinstalled on some models. So I spoke with my contact at Curt to determine if the 2011 Chevy Traverse was a model that it could be reinstalled on. He stated that they did not have information on the 2011 but on the 2010 it can be reinstalled. Basically, if the rear fascia is the same on the 2011, then it will fit. But if it has been redesigned, it will...
  view full answer...
• Draw-Tite Trailer Hitch Receiver with Installation Hardware for a 2008 GMC Acadia
  The 2008 GMC Acadia Draw-Tite Max-Frame Trailer Hitch Receiver Class III - 2" # 75528 is a quality choice for your vehicle, and it comes with all the hardware you'll need for installation. If you plan on towing, you'll want to grab a wiring harness and ball mount set-up as well. Wiring harness for a vehicle without a tow package # 118451 Wiring harness with tow package # 118384 I recommend the etrailer Ball Mount Kit # 989900. It comes with 2 ball mounts, 2 balls, a hitch pin with clip,...
  view full answer...
• Draw-Tite Hitch # 75362 Fit on 2000 GMC Sierra
  The Draw-Tite Class III Hitch # 75362 that you referenced is a correct fit for the 2000 GMC Sierra 1500 and 2500 LD truck with OEM bumper. The hitch installs without drilling using included hardware. The written instructions as well as an install video are linked for your review. If you have a different version of the Sierra please let me know and I will be glad to confirm a hitch fit. I have also included two articles concerning hitch installation that will be helpful to you. If you...
  view full answer...
• Trailer Wiring Stopped Working After Turning On Hazard Lights on a 2006 Nissan Titan
  If everything was working but then stopped working as soon as you used the hazards then I think it is fuse or relay related. There could be a short issue of some kind that is not all that bad when just one blinker is working. But with both blinkers going on at the same time, the power draw increases and that could have caused a fuse or relay to fail. For relays you could use # C57000. But I would not replace anything until you have examined all of the wiring and checked for exposed wires...
  view full answer...
• Troubleshooting 2014 Ram 3500 Trailer Brake Controller Not Sending Power To Trailer Brakes Suddenly
  I would be happy to help! First things first using a circuit tester like # PTW2993 test the 5 o'clock pin on your 2014 Ram 3500's 7-way connector while a friend applies the manual override to the controller. If you are getting power, there then this means the issues is between your trailers 7-way connector and the brake magnets. You will want to check all of this wiring for any damage and replaced damaged sections with # 10-1-1 and heat shrink butt connectors # DW05745-5. If you do NOT...
  view full answer...
• Connecting 3rd Brake Light of Truck Camper Shell to 2013 GMC Sierra Wiring Harness
  For connecting your truck shell 3rd brake light on your 2013 GMC Sierra 1500 I recommend adding the Tekonsha T-One Vehicle Wiring Harness # 118384. This will allow you to be able to unplug the wiring that will go to your truck shell if you need to remove it from the truck. It will also not require you to splice into any of your vehicle wiring. To this you will need the Wesbar 4-Pole Flat Connector # W787268 to allow you wiring up to your 3rd brake light. You will then be able to wire...
  view full answer...
• Troubleshooting Brake Controller Errors When Running Lights Or Hazard Lights Are Turned On
  Hey Michael, The first thing I'd check is the ground both on the truck's 7-way because a weak ground causes all kinds of goofy issues. I'd just splice into the back of the factory 7-way and run a 10 gauge wire # 10-1-1 to the vehicle frame with a ring terminal # 44-5356A and self-tapping screw. I'd also check that there's not bare or damaged wires touching each other behind the 7-way. From there I'd start to question that the brake controller is properly functioning. You've already...
  view full answer...
• Part Needed to Add Second 4-Way to Rear of 2016 Ford F-150
  What you could use is the part # 118384. This 4-way will plug in line with the 7-way you have at the rear of your 2016 Ford F-150 and it will provide you with an additional 4-way at the rear of your truck.
  view full answer...
• Is Under Car Trimming Required for Installation of Hitch # C13065 on a 2011 Dodge Grand Cherokee
  For installation of the Curt Trailer Hitch, # C13065, on your 2011 Jeep Grand Cherokee, you will need to trim excess caulk on vehicle frame rails, only if it interferes with hitch installation, see instructions link. I have added a photo showing where the excess caulk is likely to interfere and need to be trimmed. No part of the bumper or fascia will need to be trimmed. You may be interested in the following items to complete your trailer hitch setup. Trailer Wiring, # 118425 (without...
  view full answer...
  
• Interior Lights In Horse Trailer Not Working After New Tow Vehicle
  If the only thing that has changed on your trailer is that it is now being pulled by a different vehicle then that is most likely where the issue resides. Generally speaking, the interior lights are powered by either a 12 volt battery on the trailer and is then charged by the 12 volt power circuit on the 7-way or they are just ran directly to the 12 volt power circuit on the 7-way. Therefore, the issue you are having is most likely that the 12 volt power circuit on the 7-way is not active...
  view full answer...
• Availability of Plug-In 4-Pole Trailer Connector for 2000 Chevrolet Silverado
  If your 2000 Chevrolet Silverado has a factory 7-way trailer connector with a round U.S. Car connector at the back (please see photo) you can use part # 74682 to provide both 7-way and 4-pole connectors in one housing. If you prefer them to be separated then instead you can use harness # 118384 which will connect inline with the existing 7-way's connectors. Both connectors will be active at the same time. You also have the option of wiring in a totally separate universal 4-pole trailer...
  view full answer...
  
• Running Light Circuit on Truck Side 4- and 7-Way Connectors Does Not have Power
  The flashers are on a different circuit than the running lights on a 7- or 4-Way. Brake lights and turn signals are combined on one circuit. The running lights do not share a circuit. So since there is no power on the running light circuit I suspect that it is a tow package fuse or relay that is blown or missing. Check the vehicle owners manual to find the locations of the tow package fuses and/or relays. If there is a blown fuse then you would want to determine where the short occurred...
  view full answer...
• Adding a 7-Way Trailer Connector to a 2012 Dodge Ram 2500 Big Horn With Flatbed
  If your 2012 Dodge Ram 2500 came with a factory tow package that included a 7-Way at the back of the vehicle, you can use 5th wheel and gooseneck in-bed wiring harness, # 50-97-410. This harness plugs in line with the factory wiring harness under the truck and provides a 7-Way in the bed area. If the truck did not come with a factory tow package that included a trailer connector, you will have to hardwire one in starting with a 4-Way using # 119178KIT. A T-connector is not available. Once...
  view full answer...
• Does Third Brake Module PP20-702 Fit 2020 Ram 1500
  Yes the third brake light module part # PP20-702 that you referenced does fit your 2020 Ram 1500. You'd want to wire this to the trailer wiring at the rear of the truck.
  view full answer...
• Trailer Running Lights Not Working when Using a 7-Way to 4-Way Adapter
  I assume you meant 7-Way since there are no 8-pin connectors. The 7-Way to 4-Way adapters will have the pins in the standard locations for the trailer lights but no other pins will be present. Rather than changing the pin out on the adapter it would be easier to swap wires around on the vehicle side 7-Way connector to the positions you need. The 7-Way trailer connector can be opened up and the wires switched around. If your 7-Way cannot be opened then you will have to cut and splice the...
  view full answer...
• Right Brake Light on 4-Pole Trailer Connector Not Working on 2004 GMC Sierra
  If your 2004 GMC Sierra uses a 4-pole flat trailer connector like the Tow Ready # 118384 that you referenced the right turn and right brake light signals both will be carried on the green wire. Please refer to the linked photo. The most common cause for one light function (the right turn light) to work while another carried on the same wire (the right brake light) does NOT work is a bad ground connection. Turn signals do not pull as much current as a brake light signal, since turn signals...
  view full answer...
  
• Is The Tekonsha T-One # 118384 Compatible With The Brake Controller 9030A?
  The T-One Vehicle Wiring Harness # 118384 would not be compatible with the Tekonsha Brake controller you mentioned. The 118384 is a 4 flat wiring harness for trailer brake lights, tail lights and turn signals. So it does not include any kind of brake function. You would need to have a 7-way plug installed on your vehicle in order to use a brake controller. If you have a 7 way plug installed from the factory your can use part # 7894 to wire in your brake controller.
  view full answer...

Do you have a question about this Custom Fit Vehicle Wiring?