Bolster Bracket - Zinc Plated Steel - 10-1/8" Tall x 2-1/2" Wide x 1" Deep - Qty 1
(0 reviews)
Price: $14.41
In Stock
Bolster Bracket - Zinc Plated Steel - 10-1/8" Tall x 2-1/2" Wide x 1" Deep - Qty 1
Item # HP85FR
Our Price: $14.41
In Stock
Need help with installation?
Locate installers near me- All Info
- Q & A (0)
- Videos (1)
- Photos
etrailer Boat Trailer Parts - HP85FR
- Bunks
- Bunk Bracket
- 10-1/8 Inch Tall
- Zinc-Plated Steel
- 2-1/2 Inch Wide
- etrailer
Mount your boat trailer's bunk board using this rust-resistant bolster bracket, which helps support your bunk when used with a swivel bracket (sold separately). Single slot lets you adjust the bracket height. Dimpled surface resists sliding.
Features:
- Bolster bracket lets you attach a swivel bracket (sold separately) for mounting a bunk board to your boat trailer
- 2 Brackets are required to mount 1 bunk board (additional bracket sold separately)
- Dimpled surface helps prevent the bracket from sliding along your trailer's frame
- Mounting slot lets you adjust the bracket's height during installation
- Bracket installs vertically on your boat trailer's frame
- 11-Gauge, zinc-plated steel resists rust and corrosion
- Made in the USA
Specs:
- Quantity: 1 bracket
- Dimensions: 10-1/8" tall x 2-1/2" wide x 1" deep
MBA00002 Bolster Bracket for Boat Trailers - Zinc-Plated Steel - 10.125" Tall x 2.5" Wide x 1" Deep - Qty 1
Video of Bolster Bracket - Zinc Plated Steel - 10-1/8" Tall x 2-1/2" Wide x 1" Deep - Qty 1
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Review of etrailer Boat Trailer Parts - Bolster Bracket - HP85FR
Ellen: Hey everybody. I'm Ellen here at etrailer.com and we're taking a quick look at the bolster bracket for your trailer. This is going to help you get your bunks in the right position so that your boat can slide in easily and have that nice close fit. So these can be adjusted height-wise to get you at the right angle to fit on there. Your swivel brackets also going to go on to adjust to the contour. Swivel brackets are sold separately, we have a lot of other hardware here at etrailer.com as well.Let's take a closer look and make sure that this is the right size for you.
So the total length of our bracket here is about 10 and an eighth inch long, and then about two and a half inches wide, an inch deep. The slot for the adjustment and height is about six inches long. You can see those dimples there that helps to prevent it from just sliding down on your trailer, so it should keep it at the right height. The diameter of the mounting hole and of the slot itself is about half an inch. It's made out of an 11 gauge steel with a zinc coating, so it should last you a long time without any worries about rust or corrosion.
You also should keep in mind that you'll need two of these brackets to mount one bunk board and also two swivel brackets as well for that complete setup. Again, you can find those swivel brackets here at etrailer.com and all kinds of parts and accessories for your trailers in general. So be sure to check them out and thanks for watching..
0
0
See what our Experts say about this etrailer Boat Trailer Parts
Info for this part was:
Edited by:
Lindsey S
Installed by:
Kathleen M
Written by:
Alexander C
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.