Bottom Support Plate for 2-1/4" OD A-Frame Jacks - 5,000 lbs
(49 reviews)
Price: $5.74
In Stock
Bottom Support Plate for 2-1/4" OD A-Frame Jacks - 5,000 lbs
Item # JSP-100
Our Price: $5.74
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (49)
- Q & A (0)
- Videos (1)
- Photos
etrailer Accessories and Parts - JSP-100
- Camper Jacks
- Trailer Jack
- Mounting Hardware
- Plates
- etrailer
Attach a layer of support when mounting your jack to your A-frame trailer coupler. Fits 2,000-lb to 5,000-lb A-frame jacks. Raw finish with light oil allows for easy welding.
Features:
- Support plate adds stability to help keep your A-frame trailer jack from leaning
- Bottom-mounted plate attaches to the underside of your trailer frame
- Sturdy steel construction
- Weld-on installation
- Raw finish for easy welding
Specs:
- Fits jacks with 2-1/4" outer tube diameter
- Jack hole diameter: 2.29"
- Weight capacity: 5,000 lbs
- 1-Year warranty
JSP-100 Ram Bottom Support Plate for 2-1/4" A-Frame Trailer Jacks - 2,000 lbs to 5,000 lbs
Video of Bottom Support Plate for 2-1/4" OD A-Frame Jacks - 5,000 lbs
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for etrailer Trailer Jack JSP-100 Review
Today, we're going to be taking a look at a bottom support plate for a 2-1/4" outer-diameter A-frame jack with a capacity of 5,000 pounds. This support plate is going to add stability to keep your A-frame trailer jack from leaning under heavy loads. It's a bottom-mounted plate that attaches to the underside of your trailer frame. It's made from a sturdy steel construction. This is a weld-on installation. It's a nice raw finish for easy welding, so there's no prep work for it. This is designed to fit jacks with a 2-1/4" outer-tube diameter.
We can tell that by taking a measurement of the diameter of the hole right here at the center of the plate. It's going to be just a hair over 2-1/4". The exact measurement is going to be 2.29", but it is designed for a 2-1/4" outer-tube-diameter jack. Again, it's going to have a weight capacity of 5,000 pounds. A few measurements I want to go over with you real quick. The thickness of the plate is 1/8".
Again, steel construction. If we take an overall length measurement here at the back, that's going to give a measurement of 8-3/4". Here at the front, that length measurement is 5-1/2". The diagonal measurement right here, it's going to be the same for the other side. That's going to measure 3-7/8".
Then from front to back right here at the center, the straight-line measurement is 3-1/2". That's going to do it for today's look at the bottom support plate for 2-1/4" outer-tube-diameter A-frame jacks.
Customer Satisfaction Score:
100% were satisfied with this product
0% of customers were not satisfied
Customer Reviews
Bottom Support Plate for 2-1/4" OD A-Frame Jacks - 5,000 lbs - JSP-100
Average Customer Rating: 4.7 out of 5 stars (49 Customer Reviews)
Attach a layer of support when mounting your jack to your A-frame trailer coupler. Fits 2,000-lb to 5,000-lb A-frame jacks. Raw finish with light oil allows for easy welding.by: Jrzoffroad03/16/2024
A great and quality item to mount your trailer jack to.
by: David 02/12/2024
No longer have that trailer. But did the job..
by: Grant 08/07/2023
Buying this was the easiest part of replacing the bottom plate to my trailer. I had no issues with it other than things on my trailer itself and my bad harbor freight welder. These guys really helped make this less of a headache for me.
by: Bill 06/20/2023
A must for a frame jacks
by: Steven07/09/2020
It needs to be thicker metal. My trailer came with one exactly like this one from the factory. Someone before me tried to drive off with the jack down and ripped through the old one. Which in turn bent the L out of the hitch. The hitch was so bent there was no way to repair it and mount a new jack. So I am having to replace the hitch as well as this weak plate. If this piece had been strong enough to hold instead of tearing in two, it wouldn't have bent the hitch. The jack would be ruined but then the jack was ruined anyway. It would only have cost the price of the jack. Not the jack, hitch, and this plate. Probably order a second one and add to this one. It needs to be at least twice as thick.
by: David10/27/2022
Storage crew told me to STOP when I backed into the building...when my RPod popped off the hitch ball it rolled forward about three inches, bending the existing jack mount plate and leaving the jack at an approximately 15-degree angle. Mad? -- you bet...THIS will support the lower side of the jack after the trailer repair outfit straightens the upper mount. Thanks!
by: Dust09/12/2023
Good shape to reinforce my larger diameter Jack
by: Micah 04/06/2023
these where just what I need to fix a couple of my trailers
by: James 05/31/2023
Very well made for a bottom support. The original was double the thickness, but this should be fine for the purpose it is used for.
by: Sandy G08/14/2017
While these may be good to weld on, most of the trailer jacks that I have seen are the 3 bolt triangular style. These don't work well with them since the front part is too short to cover the entire bolt hole. So these would only be useful in a weld on style jack configuration, not a bolt in.
by: Robert06/18/2023
Heavy duty lot better than stock
by: Christopher 04/27/2023
Easy to weld in place.
by: Tex-Ag03/08/2023
I would have given the product an excellent rating but the manufacture did not de-bur the cut edges. Luckily no one got cut. After de-burring the cut edges with a bench grinder the product was what would be expected.
by: Matt P07/03/2017
etrailer exemplifies customer service. On top of providing one of the widest selections of quality products their follow through and fast shipping keep me coming back for more.
by: John 11/17/2019
I used two of these to convert my side mount jack to an A frame jack without replacing my hitch receiver. With a few modifications they work great! Super happy!
by: Dan J08/28/2019
The product I received was exactly what I ordered and appears to be of excellent quality. It was delivered in a timely manner with no issues.
I have purchased other items from etrailer.com and expect to purchase more in the future!
by: Cliff B07/18/2020
Exactly what I needed. Even got to practice my limited welding skills to put it on. Hardest part is cleaning up the mess the old rusted out on left. I primed a painted this one after installing.
by: Shane 01/30/2023
The delivery was earlier than expected.The part is exactly as the description.
by: Ryan06/13/2016
The plate is as described. Unfortunately does not cover all holes on trailer completely.
by: Mike 11/21/2020
I’m rebuilding a 1977 Jayco Finch pop-up trailer. With a little trimming this bottom support worked great! Just like OEM.
by: James08/22/2019
Prompt delivery. Just what I needed. Adds much stability to my jackstand.
by: Robert P10/04/2020
Product was great fit perfectly and easy to install!
E Trailer shipped the part out right away, really happy with their service.
by: Wallace B10/03/2019
This is 1/8 inch steel So it’s really hard to weld. If they made it with a thicker material I think it would be a lot better.
by: Rod 02/27/2021
I welded it to the frame and it holds s olid.
by: Jacob 04/17/2024
25
49
Show More Reviews
See what our Experts say about this etrailer Accessories and Parts
- Availability of A-Frame Trailer Jack With Tube Diameter Of 1-7/8" or Less For 1967 Vintage TrailerI do have an option for you, but there is not an A-Frame trailer jack offered with a 1-7/8" or smaller outer tube diameter as 2-1/4" is the standard. What you will need to do is replace your bottom support plate with the # JSP-100 instead as this has the 2-1/4" opening to match your upper hole. Once that is done you can use any of the A-frame jacks as the 3 bolt 3" bolt pattern you have is standard, but based on the specifics you were looking for I recommend the Buyers Products A-Frame...
view full answer... - Recommended Jack Support Plate When Installing Demco A-Frame Trailer Coupler DM14791-97For the Demco A-Frame Trailer Coupler w/ Jack Hole - eZ-Latch - Primed - 2" Ball - Weld On - 10K # DM14791-97 you were looking at you can use the Bottom Support Plate for 2-1/4" OD A-Frame Jacks - 5,000 lbs # JSP-100 to replace your current jack support plate. I included videos for each of the products mentioned for you to take a look at.
view full answer... - Footplate Recommendation for the etrailer Round A-Frame Jack # TJA-5000S-BI believe you are looking for a footplate for the etrailer Round A-Frame Jack, # TJA-5000S-B. If so, then you can use the Footplate for 2,000-lb and 5,000-lb Round, A-Frame Jacks # JF-99. This foot plate attaches to the inner jack leg using included pin. Since you will be installing this jack on a dump trailer, I recommend using the Bottom Support Plate for 2-1/4" OD A-Frame Jacks - 5,000 lbs # JSP-100. Dump trailers can be loaded pretty heavy, and this plate will help support the jack...
view full answer... - Steel Thickness for A-Frame Trailer Jack Support Plates for 2-1/4 Inch JacksThe A-frame trailer jack support plates for 2-1/4 inch jacks are all approximately 1/8 inches thick. There are some manufacturer tolerances so one might be slightly thicker than the next. And models that are raw steel like # BD003135 are more uniform in size compared to the ones that are powder coated. I have included a link to the options. Not all of them are for 2-1/4 inch jacks and there is also a square one in there but the majority are for 2-1/4 inch round jacks.
view full answer... - Recommended Plates for Installing Electric Jack Mount on A-Frame TrailerThanks for the photos. You will need to weld on a plate like the Bottom Support Plate for 2-1/4" OD A-Frame Jacks - 5,000 lbs # JSP-100. It sounds like you will need a couple of these plates to create a bracket instead of a reinforcement because it will need to be strong enough to support the tongue weight of the trailer. Then the Stromberg Carlson Electric Trailer Jack - Drop Leg - A-Frame - 23" Lift - 5,000 lbs - Black, Item # JET-5000 is a great option for your trailer.
view full answer... - Dimensions of Lippert Smart Jack Above The Frame For a Boat Trailer JackThe Lippert Smart Jack Electric Trailer Jack w/ Footplate # LC643589 has the following dimensions above the mounting plate. It is 21.6" tall, 6.165" wide at the widest point of the head and 9.385" deep at the widest points. I have included an image to help you see these measurements. The manual override nut on the jack is a 19mm hex head bolt. I recommend the Bottom Support Plate # JSP-100 for helping you to create a mount on the frame of your boat trailer to hold the Smart Jack.
view full answer...
- Will the Stromberg Carlson Electric Trailer Jack Work with a 20' Tandem Axle 14k Tilt Deck TrailerFrom what I can find, the square jacks coming on the trailers like your 20’ tandem 14k tilt deck trailer are 5,000 lb. capacity square jacks. The Stromberg Carlson Electric Trailer Jack # JET-5000 has that 5,000 lb. capacity and is an electric option. It does have a bolt-on installation, but can be welded if necessary. It typically goes through a hole in the coupler intended for the jack and then mounts with 3 bolts. You could also think about welding on a couple of the Support Plate for...
view full answer... - Highest Lift for A Frame Trailer Jack With 5,000 lb Weight CapacityWe have a jack that meets all of the requirements that you are asking about. The Round A-Frame Trailer Jack # TJA-5000S-B has a lift, or travel, of 15-5/8 inches. When this jack is fully extended, the bracket height it 24 inches. This jack also features an easily accessible grease zerk for maintenance and has a support capacity of 5,000 lbs. Since this jack doesn't come with a foot, I recommend using part # JF-1005H-Z to help stabilize your trailer. If you would like a bottom support plate...
view full answer... - Dimensions Of Bottom Support Plate JSP-100The Bottom Support Plate for 2-1/4" OD A-Frame Jacks - 5,000 lbs # JSP-100 you mentioned is 1/8" thick, has a hole diameter of 2.29", 8-3/4" long at the back, 5-1/2" long at the front, the diagonal sides are 3-7/8", and front to back is 3-1/2" as shown in the included diagram. I included a video of the # JSP-100 for you to take a look at.
view full answer...
- Recommended A-Frame Jack Mounting Support Plate For Standard 3 Inch On Center MountThe Lippert Components # LC285318 uses a standard 3 inch on center bolt pattern. You will most likely need to drill some new holes in your coupler to allow for the standard mounting when replacing your trailer jack. I recommend the Bottom Support Plate for 2-1/4" OD A-Frame Jacks - 5,000 lbs # JSP-100 if you are concerned about the stability in that location with the additional holes.
view full answer...
Do you have a question about this Accessories and Part?
Info for this part was:
Installed by:
Cole B
Updated by:
Wilson B
Updated by:
Ronnie R
Updated by:
Mike S
Written by:
Amanda M
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Steven
7/11/2021
Like my original post, it needs to be thicker, but it works like it should. A must have for all trailers not equipped with it from the factory.