Highest Lift for A Frame Trailer Jack With 5,000 lb Weight Capacity

Question

Question:

Looking for a bolt mounted A trailer jack, side wind with aprox. 5000lb capability with the highest lift available. What in your product line fits?

asked by: Wendell

0

Expert Reply:

We have a jack that meets all of the requirements that you are asking about. The Round A-Frame Trailer Jack # TJA-5000S-B has a lift, or travel, of 15-5/8 inches. When this jack is fully extended, the bracket height it 24 inches. This jack also features an easily accessible grease zerk for maintenance and has a support capacity of 5,000 lbs. Since this jack doesn't come with a foot, I recommend using part # JF-1005H-Z to help stabilize your trailer.

If you would like a bottom support plate for this jack then I recommend using part # JSP-100.

expert reply by: Jon G

0

Answer 1

I spoke with my contact at Optronics, and the part you were looking at, part #APL1AB, should fit your Bargman Light. The Clear lens versions is part #APL1CB. I have added links to these two parts below.

view full answer...

Answer 2

From what you described I believe that you are correct that the Drop Leg for etrailer and Ram Jacks #JF-1005H-Z will fit the jack on your Jayco Jayflight SLX 174BH Trailer. This is designed to fit inside a jack with a 2" outer diameter tube like…

view full answer...

Answer 3

The Atwood jack 80274 was an A-frame type side-wind tongue jack with a 2K weight rating which we have several options for that would work great as a replacement. The Pro Series Round, A-Frame Jack w/ External Gearbox #PSRV20000103 that you referenced…

view full answer...

Answer 4

Thanks for the picture of your jack. From that I can tell that you have the Round A-Frame Trailer Jack #TJA-2002-B and the correct replacement foot you'll need is the #JF-1005H-Z that you mentioned. This will give you up to an additional 8 inches…

view full answer...

Answer 5

Based on my research the Atwood jack 80274 was an A-frame type side-wind tongue jack with a 2K weight rating. The Pro Series jack #PSRV20000103 that you referenced is a suitable replacement for this discontinued product. The Pro Series offers a 2K…

view full answer...

Answer 6

On Pro Series trailer jack #PSRV20000103, the pin hole on the lower leg is approximately 3/8 of an inch in diameter. It is actually just slightly larger. For a foot that will fit you can use #PS1400700340. Or for a wheel use #PS1400750340. The wheel…

view full answer...

Answer 7

?The distance from the mounting plate to the foot on the Trailer Valet JX-2K #TV54FR is 13" when fully retracted. The distance from the mounting plate to the top of the jack is 23". This jack can provide you with up to 14" of lift on…

view full answer...

Answer 8

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

I contacted the manufacturer about the lengths for these stabilizer jacks and have included the information they were able to provide me. The Ark Drop Down Corner RV Stabilizer Jacks #ARK34FR are 422 mm (16.6") collapsed and 600mm (23.6")…

view full answer...

Answer 11

Your typical electric jack is designed to fit an A-frame so the only one we carry that is a side mount is the Fulton XLT #F141401. However, you may be interested in the Trailer Valet JXS Drill Powered Swivel Trailer Jack #TV64FR. This jack has a hand…

view full answer...