Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
7" x 1-3/4" Driver's-side hydraulic trailer brake assembly features a single-plunger design. Mounting flange has 4-bolt pattern. Fits 10" to 13" wheels.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we're gonna take a look at the Dexter seven inch left=hand driver side hydraulic drum brake assembly for 2500 pound axles. The hydraulic drum brake assemblies are designed for use with a serge type trailer brake actuator. These happen to be a uni-server design, which means it's a single plunger design. These are also manual adjustment breaks so they do require periodic manual adjustment. Right down here is the adjustment here where you'll turn the gear to adjust them in or out. Now, on the very back here, there is a access hole that they have in the backing plate that allows you to put your tool through there to adjust your brakes and, what's nice about this assembly, if you notice they have a plug in there. They do include these adjuster plugs, which will cover those access holes to keep dirt and grime out of your assembly and off the brake shoes. Now, this part does include the left-hand driver side break assembly and the mounting nuts to install it.
The dimensions on this is seven inches by one-and-three-quarter inches. The seven inches would be the diameter from this shoe to this shoe so, if we put a ruler on it, there's your seven inches. The one-and-three-quarter inches is the width of the pad on the shoes so there's your one-and-three-quarter inches. If you notice, it has the four bolts on the back so it does use a break mounting flange bolt pattern of four bolts. I've mentioned the four nuts are included to install it. This does require the use of a seven inch break drum.
The wheel size that'll fit on this assembly is the 10 inch, 12 inch and 13 inch and, again, it's inaudible 00:01:22 designed for axles rated up to 2500 pounds and this is a left-hand design and the way you can tell that . now on a new assembly it'll have this sticker there but, if that sticker wasn't there, the easiest way to tell is look at the length on the pad of the shoes. This pad goes from here to here. This one's from here to here. This is the shorter pad.
This is the longer pad. The shorter pad is always your primary shoe. That faces the front of the trailer so that tells you it goes this way. That means this is the left-hand driver side assembly but that should do it for the review on the Dexter seven inch left-hand driver side hydraulic drum break assembly for 2500 pound axles.
Average Customer Rating: 4.7 out of 5 stars (20 Customer Reviews)
7" x 1-3/4" Driver's-side hydraulic trailer brake assembly features a single-plunger design. Mounting flange has 4-bolt pattern. Fits 10" to 13" wheels.You delivered electric brakes not Hyd
No problem on installing the new backing plate. Just one two three and your done.
My grandson did half the work and hes is only 11 years old.
Thank you to all those personnel that assisted in processing my order so expeditiously. Have a wonderful evening.
One of the best projects I ever did. Love the results. Everything worked, fit and preforms as expected. The customer service helped me order the correct parts, the first time. Replaced lines, hubs, bearings, drums, brakes, everything.
First Rate.
Nathan B.
11/18/2020
Everything worked great and still does. Thanks to the help from the etrailer Team
I Purchased these brakes to use On a Kimball Hauler UTV, they worked great.
Installed this on my 1995 Jayco 1206 tent trailer. Went on easily, and worked great. Had to file the edges of the shoes alittle as it was rubbing the drum but other than that was great. Once the drum is off just 4 bolts and disconnect the brake line, then adjust the pads. Easier than just changing pads alone.
Drum brake assembly is exactly what I needed to replace some old and really worn brakes on a 1982 tent trailer. I was a bit skeptical as to if they would fit as there is no OEM parts out there but it turns out these were perfect!!
The easiest method for repairing trailer brakes. etrailer was great will back again
Cheaper than everyone here in Canada, parts are the same ones sold here in Canada
New brakes for 30-foot long Houseboat trailer
Etrailer is the best !!
Lighting fast shipping..great product.
Worked perfect quick delivery
Excellent price, came with everything needed to install, and good quality.
Complete, easy to install
good product worked great
Worked just like OEM.
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Tim
6/9/2018
Excellent I have then on both axels on my boat trailer