Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
In-stock alternatives that can ship today
Attach your trailer connector mounting bracket to your vehicle without having to drill. Just affix this sturdy steel bracket to your trailer hitch with the included hose clamp, and then quickly and easily bolt on your connector bracket.
Features:
Specs:
Average Customer Rating: 4.6 out of 5 stars (269 Customer Reviews)
Attach your trailer connector mounting bracket to your vehicle without having to drill. Just affix this sturdy steel bracket to your trailer hitch with the included hose clamp, and then quickly and easily bolt on your connector bracket.
Great accessory used to mount 7 round tow harness female plug on driver side of curt receiver hitch up against the tow chain attachment flange, made for a clean install!!
It does not work for the Honda Passport Trailsport. The hitch sits behind and above the bumper and there is no where that it can be mounted that would give you access to the plug. I had to use a 90 degree metal plate and then mount the bracket to the side of the hitch.
This worked great. I have a class V hitch and there is no room to put the wiring, with this was able to move the trailer wiring up out of the way. Install was easy and it seems solid so far.
I am having a problem with the install of the three Curt trailer components I purchased. I intentionally bought all of the same brand assuming that they would work together. The problem is that the Curt wiring harness (part# C55774) is too long and rigid. When the 7-pin connector is installed in the bracket that comes with it, it measure 5 inches until the black wire protective sleeve bends (to go under the hitch receiver frame).
The no-drill bracket (part# C57202) is supposed to attach the harness bracket to the hitch. But it is only 6.5" long, and the hitch tube is 3" wide. So with the bracket attached to the hitch, there is only 3.5" of space left to mount the harness bracket so that the screw holes line up.
I am disappointed that this is the case, especially as I called etrailer to check that the parts I was ordering would work together.
It looks like I will have to discard C57202 and drill two holes into the bottom of the hitch and mount the harness bracket directly. This is what I wanted to avoid - having to drill holes.
Very helpful and sympathetic. Some of the video instructions was not applicable to my model truck wiring colors. They hung in the through most of the tasting until I found the right wire for the 7 way hitch install.
Great product, works as expected, and easy to install thanks to video provided. Gave it 4 stars vs 5 as clamp provided for trailer mounting bracket was too short. This was after confirming size with representative over the phone. Short bracket and long bracket offer the same 4-inch strap to secure onto hitch. My trailer hitch measures 3.5 x 3.5 inches, ended up securing long plate with large tie strap. Also hardware supplied to fasten bracket should be stainless steel but that's an easy upgrade to complete.
Needed to replace my trailer connector as my oem was broken and also my oem hitch as well. Mike Lindsay made it happen for me to make sure i could get my connector and proper mount to work.
I applaud etrailers website but most importantly the staff that communicate and share INvaluable guidance to get a product chosen. Good people + good products = good business. Im happy! Thanks!
Easy to install. My 7 way feels nice and solid. Would recommend for anyone who doesn’t want to drill into their bumper. Just check if you need to hang under or over before mounting the 7 way plug.
Went together without any problems, I pre-assembled the two brackets ( 7-Way Round Trailer Connector Mounting Bracket - Long - C57202 and the Pollak 7-Pole, RV-Style Trailer Connector - Vehicle End - PK12711U) then crawled under and put the clamp around the Curt Trailer Hitch Receiver - Custom Fit - Class V - 2" that I bought along with this purchase and snapped in my existing 7 way and it was all set up. Very sturdy, though I was concerned with how stable it would when I purchased it. Turns out it is really solid, very happy with the setup. The hitch is a really beefy, so I'm quite pleased with it as well. I did enlist the help of a friend to get it up into place, which I think was the easiest path. If one had to, you could do it alone, but so much easier with a couple of extra hands. All in all, probably took 2 hours for the complete install.
I had a standard OEM hitch that I had used to attach a 9000 lbs pull capacity winch to pull up trees on my property, consequently, it stretched/hogged out my 5/8" pin hole, so every time I stopped or started with a trailer, it would slap around. Turns out the OEM hitch is rated for 7500 lbs, this Curt Hitch is rated at 16,000, so I should have no future problems. I'm happy with the setup. I expected that Curt would have engineered a better way to attach the 7 way when they designed the Hitch, I expected better from them.
Installed it myself and towed my camper from NC to Cali with it! Worked great and held up the whole time!
The Curt No-Drill Bracket worked absolutely perfect for my Drawtite hitch on my 2016 Subaru Outback. Super easy installation and the hose clamp worked a lot better and tighter than I expected it to. I would highly recommend this product if you are wanting to mount your wire harness to your hitch!
This is holding good stikl. It rotates a little bit every other week, but it is still holding. I hope it lasts.
I was surprised at how sturdy this installation is. etrailer sure helped me out along the way with this installation. Special thanks to Alex J for his help on several occasions to help me get the right hitch and accessories for my new 2021 Hyundai Palisade Calligraphy.
Nice mount. I added no slip tape to the hitch to help prevent mount from wearing thru the powder coat finish on the hitch. Nice, easy and clean setup.
Works as expected. Clamp screw slips a bit when starting to tighten. I would have opted for the shorter bracket. This one puts the connector even with hitch receiver.
I have installed this on the bottom of the receiver hitch on our 2013 Dodge Grand Caravan with the 7-pin connector mounted on the bottom side for easier access.
Does the job and holding up well after regular use. Added a 7 way plug to my kia sorento and needed a solution to mount it. This attached easily to the factory hitch.
I had an issue with the clamp on the first one, etrailer sent me a replacement right away and it has worked great and is still holding up just fine a year+ later.
Well designed and it FITS!! The package went together with no "hitches" so to speak. Thanks again.
Clamp broke after a while. Replaced it. Other than that it, works good.
Works good so far. Just concerned with a hose clamp as a permanent connection
I didn't care for the way this bracket sat on my Curt XD receiver hitch. Because the crossbar on the hitch sits at an angle, so does this plate. I ended up fabricating my own bracket and attaching it to the bumper support.
Ordered parts for installing a brake controller.
The videos that are part of the web site were a great help in selecting all the needed parts, detailed down to the part numbers that were needed.
I really like the fact that there is a video showing the brake controller installation with my specific vehicle.
Great service !
Brian S.
12/27/2018
Working perfectly
The bracket and hardware were good, however the strap holding the bracket onto the hitch tube would not open. I called for a replacement and spoke with Dru who said He would send a new one out. I was ready to install the two brackets and had to put the project on hold.
Jenny N.
8/5/2022
We recently sent you a new hitch bracket and were wondering if you had any feedback about the product for other shoppers? We look forward to hearing from you.
We made a special 5 hour drive to etrailer, and etrailer did (Fantastic) installation work on this part as well as installing the Roadmaster Crossbar-Style Base Plate-4420-1, with Removable Arms, Wiring-RM-152-98146-7, Braking System-SM99251, Tow Bar-RM-522, Safety Cables-RM-645, and Brake Lite Relay-RM-88400 Kit on our 2011 Ford Fusion. We absolutely love this system. Ease of connectability and reliability is great. etrailer has stood tall on complete customer satisfaction and has prided themselves on doing things the right way the first time. We have a 2016 Honda Accord Touring that we are considering as a future tow vehicle, etrailer will be a clear choice. We recommend them with confidence. Thank you everyone at etrailer for great Communication, Customer Satisfaction, Service and product reliability!
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time.
Heather A.
10/26/2018
The 7-way bracket that comes with the wiring harness part # C55774 is designed to be installed with the wiring harness bracket hanging below the no drill bracket part # C57202. Since you are worried about the loose wiring I would recommend using some wire loom such as part # 459075-1 to protect your wiring and zip tie any slack with zip ties part # DW05726-25. I know this is not the option you wanted but I feel it is better than drilling into the hitch.
Helpful Links
Accessories-and-Parts/Curt/C57202.html
Custom-Fit-Vehicle-Wiring/Curt/C55774.html
Tools/Deka/DW05726-25.html