Primary Wire - 16-Gauge - White - per Foot

See what our Experts say about this Deka Wiring

• Troubleshooting No Turn or Brake Signals on a 5th Wheel Trailer
  Thank you for all of the info! The best way to determine where to start is by checking the turn and brake signals on your truck connector with a tester like part # PK12741 which plugs right into your 7-Way. The trailer lights are on a different circuit from your truck tail lights (unless you have an older truck with a splice-in wiring kit) so it's quite possible that your truck lights are working fine but the issue still lies with your truck wiring. If the tester shows that the truck...
  view full answer...
• Trailer Wiring Using Wishbone or Y-Harness 4-Way Trailer Connector
  The 20 Ft 4-Way Trailer Wiring Harness - Wishbone Style - 30" Ground # A20WB simply has two wires that connect to the running light pin of the 4-way. There isn't a 5 wire we carry in spools or by the foot, but we do carry the Bonded 4 Wire - per foot # 16-4B-1 and then you can add Primary Wire - 16-Gauge - White - per Foot # DW02359-1 for the additional running light wire. You can connect these to a 4-way flat connector using the Hopkins Endurance Quick-Fix Replacement 4-Way Flat Trailer...
  view full answer...
  
• Diagram For Brake Controller Installation on a 2006 Volkswagen Touraeg V10
  The Tech Bulletin that you were looking at, see link, is the best resource we have for installing a brake controller on the 2006 Volkswagen Touareg. I think that I can expand on the instructions a bit to make a bit of sense out of the wording, and I have a photo of the parts you should get, see link. You will need to purchase 2 wire assemblies from VW, part number 000-979-228, that will have wire terminals on both ends. You will need to cut each assembly in half to create 4 wires. The...
  view full answer...
  
• Adding 5-Way With 25 Feet of Wire to Back of Trailer For Lights on Cargo Carrier
  So I think we have a solution here for you, but there isn't a vehicle-end 5-way that has 25 feet of wire, so you'll need to splice in additional wire. As for using the blue wire, that is the reverse light wire on the 5-way, so you would need that since you want to utilize a reverse light. Here is what you would need: - Hopkins Wiring Harness with 5-Pole Flat Trailer Connector - Vehicle End - 5' Long # HM37908 - Primary Wire - 16-Gauge - White - per Foot # DW02359-1 - Deka Heat Shrink...
  view full answer...
• Can MaxxFan Plus Roof Vent W/ 12V Fan Replace Standard Roof Vent On 1998 Casita Spirit Deluxe
  The MaxxFan Plus Roof Vent w/ 12V Fan and Thermostat - Manual Lift - 10 Speed - White # MA00-04000K you were looking at will require the roof of your 1998 Casita Spirit Deluxe to be 2"-6-1/2" thick, and will require a 14" x 14" opening. If you find that your roof is not quite thick enough you can use lumber to frame out the opening to add thickness. There is no reason the # MA00-04000K will not work for your camper, but you will need to add a 12v power wire and ground wire from your camper...
  view full answer...
• Grounding Trailer Lights That are Mounted to Wood Rather than Metal
  If the lights you are using have wires coming out of the back like the Optronics Camping Travel Trailer Stop, Turn, Tail and Back-Up Light, part # RVST56, then you can simply connect an extension wire like part # DW02359-1 from the ground wire on the light to the trailer frame and ground the white wire from your trailer connector to the trailer tongue. If the lights you are using ground through the mounting hardware, then you can simply run a jumper wire from the post on the light that...
  view full answer...
• Installation of MaxxAir MaxxFan Trailer Roof Vent
  While we would not have any way to know for sure it is unlikely there is going to be wiring run. In order to install the MaxxAir MaxxFan Trailer Roof Vent # MA00-06200K you would need to use Primary Wire - 16 Gauge # DW02359-1 to run wire to a 12V power source. This vent is designed to fit standard RV roof openings of 14” x 14” and a minimum roof thickness of 1-1/8” to a maximum of 6-1/2”; it will also require the use of Sealant # 0160297 to ensure a tight bond between the flange and roof.
  view full answer...
• Recommended Trailer Breakaway Kit w/ Battery & Wiring For Enclosed Trailer
  For a breakaway kit with a battery and battery charger, I recommend going with the most reliable option, which is from Hopkins. The correct part number for this kit is the following: - Hopkins Engager Push-To-Test Trailer Breakaway Kit with Built-In Battery Charger # 20400 The Hopkins # 20400 is really easy to use, with a button you can push that give you an indicator of if your battery is charged, charging, or low. It will automatically charge the battery so you don't have to do anything...
  view full answer...
• Installation of Wiring and Switch for Ventline Ventadome Roof Vent with Powered Lift
  Correct, the Ventline Ventadome Roof Vent w/ 12V Fan with Powered Lift, # V2119-603-00 will require use of the Wall Remote Switch for Ventline Ventadome Roof Vent, # VC0533-03-A in white, or VC0533-02-A for black face plate. The Ventline Ventadome, # V2119-603-00 has two sets of wiring pigtails, see the linked product video below. Each set will require a connection to the switch, you have the powered set but will need the circuit for the on/off switch to run parallel. Use Primary Wire,...
  view full answer...
• Recommended Roof Vent With Remote For Truck Camper Shell
  For your Fiberglass Camper Shell I recommend the MaxxFan Deluxe Roof Vent w/ 12V Fan, Thermostat, and Remote - Powered Lift - 10 Speed - White # MA00-07500K due to it being able to be controlled with a remote making opening the vent or turning on the fan an easy task. The # MA00-07500K will require a 14" x 14" opening in the roof of your camper, and is designed for roofs that are 1-1/8" - 6-1/2" thick so if your roof is less than 1-1/8" thick you will need to use lumber to frame the opening...
  view full answer...
• Can the MaxxFan Trailer Roof Vent # MA00-04000K be Left Open Without Rain Getting Inside
  The only way to operate the MaxxAir MaxxFan Trailer Roof Vent # MA00-04000K without rain getting inside is to also install the MaxxAir II Rain Cover # MA76JR. If you are wanting a single-piece unit that includes a rain cover and utilizes a thermostat and a manual lift then the MaxxAir MaxxFan Trailer Roof Vent # MA00-06200K for Smoke or # MA00-05100K for White is exactly what you are looking for. All of these roof vents come with mounting hardware but you will also need some sealant like...
  view full answer...
• How To Install Cab Lights On The Roof Of A 1985 Chevrolet C/K Series Pickup Truck
  We have a variety of roof mounted cab lights for your 1985 Custom Deluxe. Although there are many different types, the majority of them will have the same installation method/instructions. The Clearance Light Kit part # CB-15AK has everything you will need to install cab lights on your truck. The first thing you will want to do is disconnect your vehicle's battery. You will then want to use the cab lights to mark out the position on the roof where you want the lights to sit. After this...
  view full answer...
• Vent Fan with Dual Switches for a 2008 Winnebago Journey
  From the description you provided it sounds like you are looking for the Ventline Ventadome Roof Vent w/12V Fan # V2119-3-533. This vent fan has the two sperate switches like you described. I have included a photo of the switches you can look at to see if it looks like what you have. We also have this available in white # V2119-1-533. If this is not what you are looking for and you can provide me with the manufacturer and model number of your current fan, I would be happy to help you further.
  view full answer...
  
• Recommended Fuse Bypasses for 2020 Chevy Sonic with Keyless Entry
  On your 2020 Chevy Sonic with keyless entry the fuse bypass kits are required. You will need the Roadmaster FuseMaster Fuse Bypass Switch for Towed Vehicle - (2) 20-Amp ATM Mini-Fuses # RM76512, and Roadmaster FuseMaster Fuse Bypass - 13" - 20-Amp Mini-Fuse # RM76511. You will also need 6-10 feet of extra wire # DW02359-1 and butt connectors # 05731-5. You will also need a 7.5 amp mini fuse for the harness. I've attached some videos as we have confirmed this works with the keyless entry...
  view full answer...
• Availability of Replacement Parts for Ventline Rounded Dome Trailer Roof Vent
  The Ventline product you reviewed, part # V2092SP-28, is a complete vent assembly intended for a rough roof opening of 14-1/4 x 14-1/4 inches. It consists of a wedge-shaped white plastic dome attached to a galvanized steel frame with hand-crank assembly, a removable screen, and a white plastic 2-1/8-inch-deep garnish (interior trim ring). Please note that this part requires an installation kit, part # 344270KITW, which consists of mounting hardware and a urethane caulk sealer. If your...
  view full answer...
  
• How Much of Each Gauge of Wire Fit Inside a Wire Loom Comfortably
  I would certainly recommend the 1/2-inch wire loom # 459075-1. It will hold two jacketed 2 wire 10-gauge wire and three jacketed 2 wire 12-gauge wire. See pictures to the right. In addition, I was able to fit comfortably eleven individual 16-gauge wire # DW02359-1 into the 1/2-inch wire loom. I also took a digital caliper to measure the exact radius of each type of wire: 10-gauge is .17 of an inch, 12-gauge is .14 of an inch and 16-gauge is .09 of an inch. The 10, 12 and 16-gauge wiring...
  view full answer...
  
• Parts Needed To Add Reverse Light Circuit To a 2020 Hyundai Santa Fe
  Normally a Tow Ready 4 Pole to 5 Pole Trailer Wiring Adapter # 20036 would be added to a Curt T-Connector Vehicle Wiring Harness # CU94FR on your 2020 Hyundai Santa Fe to give you the circuits you are needing. The additional 5th wire is tied into the reverse light circuit on your Santa Fe to power reverse lights or typically a Reverse Lockout Solenoid # T4748800. That solenoid would prevent the brakes from activating when you drove in reverse. Since you have a 7-way already you will only...
  view full answer...
• Recommended Back Up Alarm For A 2014 Chrysler Town and Country
  For your 2014 Chrysler Town And Country, I recommend either the Surface Mount Back-up Alarm - 97 DB # BK97DB you referenced or the Light-Duty to Medium-Duty Back-Up Alarm with Wire Leads - 12-24 Volts - Less than 0.3 Amp - 97 dB # PK41820. For either alarm, you can use the Pollak Light-Duty Toggle Switch - On-Off - 12 Volt - 10 Amp - 6" Wire Leads # PK34513 and just splice the hot side of the switch into the reverse light wire and then run the cold side to the alarm. You can use the...
  view full answer...
• Converting a 3-Way Northland Truck Camper Wiring Harness to a 4-Way Flat
  What you can do is to use the Quick FixTM 4 Pole Flat Car and Trailer Ends, # 48195, and not use one of the pins since you only have three wires that need to be connected. You can then use the wire you need inside of them as needed. The wires that run to the battery are most likely 10 gauge like # 10-1-1. The remaining wire is probably a 16 gauge like # DW02359-1.
  view full answer...
• Recommended Wire Gauge Needed to Extend Vent Fan Power Wire to Charge Controller
  To wire up your Ventline vent # VP-543SP the correct gauge wire needed is a 16 gauge like # DW02359-1. You will also want to use the 16 gauge buttconnectors like # DW05714 to connect the two wires. You definitely want this to be connected to a fused power source so if your charge controller isn't fused then on the 16 gauge wire you would want to wire in a 5amp fuse to protect the unit.
  view full answer...
• How to Connect a Surge Brake Actuator to Activate the Reverse Lockout Function
  There are 2 wires that are coming out of the actuator in the Titan Disc Brake Kit # T4843300. You will want to connect one to the 5-Pole connector on your trailer and ground the other one using a Ring Terminal # DW05737-1; it doesn't matter which wire is used for which purpose. If you only have a 4-Pole connector on your trailer then I recommend using the Hopkins Endurance 5-Way Flat Trailer Connector # HM47910 instead. You will want to cut off your current 4-Pole and use Butt Connectors...
  view full answer...
  
• Availability of Black and White 16 Gauge Wire
  In 16 gauge wire we only carry two colors by the foot. We have the black wire part # 16-1-1 or we have the white part # DW02359-1. In 10 gauge we only have the wire in red like part # DW02508-1 or blue like part # 10-1-1 but I think what you'd really be best served with is the 7-way upgrade kit part # HS381-9000 which comes with a 7-way and junction box and then for the wiring to run from the box to the trailer wiring you'd want the # DW04914-1 which is sold by the foot and uses the standard...
  view full answer...
• Tapping Into Vehicle Fuse Box To Install A Backup Camera System Without Splicing Factory Wires
  To wire a backup camera into your vehicle so that it only comes on when in reverse, will require tapping into your reverse function wiring. Without knowing your specific vehicle, I can't tell you the specific fuse location but your owners manual will be able to help you. If you choose to use this as your power source, I recommend you use the Firestone Fuse Circuit Tap Kit # F2526 and run wire like the 16 gauge # DW02359-1 to the camera wire. Another method of installation requires splicing...
  view full answer...
• Is There a Class II Trailer Hitch Receiver Available for a 2008 Chrysler Sebring Convertible
  The only trailer hitch receiver option for your 2008 Chrysler Sebring Convertible is the Draw-Tite Sportframe # 24871, which is only a Class I hitch. Due to the design of your Sebring, there are no Class II options available. This trailer hitch has a Gross Trailer Weight (GTW) of 2,000 lbs and a Tongue Weight (TW) of 200 lbs. I checked an online version of a manual for you Sebring and if had the same weight capacities that this hitch has, but you will want to check your copy of the owner's...
  view full answer...

Do you have a question about this Wiring?