Summer Starts Here - Save up to 70%
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
In-stock alternatives that can ship today
Hub is made for use on trailer idler axles. Fits 2K E-Z Lube and Easy Grease axles with BTR spindles. Inner bearing (L44649) and race, outer bearing (L44649) and race, grease seal, grease cap, and lug nuts included. Fits 13" to 15" wheels.
Features:
Specs:
The grease cap on this hub is specially designed to work with your Dexter E-Z Lube or etrailer Easy Grease axle to make lubricating bearings quick and easy. Just remove the plug on the grease cap, attach a grease gun to the zerk fitting on the end of the spindle, and inject the grease. It will flow easily to both inner and outer bearings. Not only does this make lubricating the bearings easy, but it also helps to prevent corrosion of the hub. This is because you can lubricate the bearings without the mess of taking apart the entire assembly.
The first number in the bolt pattern is the number of bolt holes. The second number denotes the diameter, in inches, of the circle on which the bolt holes sit.
On wheels with an even number of bolt holes, measure from the center of one bolt hole to the center of the hole directly across from it. (Example: 8 on 6-1/2 means 8 bolt holes with 6-1/2" from the center of one hole to the center of another on the opposite side.)
To determine the bolt-circle diameter on wheels with an odd number of bolt holes, measure from the center of any bolt hole to the point halfway between the two bolt holes directly across from the first. (Example: 5 on 4-1/2 means 5 bolt holes with 4-1/2" measured to a point halfway between the opposite bolt holes.)
Measuring the distance (D) from the center of one bolt hole on the wheel to the center of a bolt hole right next to it can also help to determine the bolt pattern.
Average Customer Rating: 4.7 out of 5 stars (40 Customer Reviews)
Hub is made for use on trailer idler axles. Fits 2K E-Z Lube and Easy Grease axles with BTR spindles. Inner bearing (L44649) and race, outer bearing (L44649) and race, grease seal, grease cap, and lug nuts included. Fits 13" to 15" wheels.
Purchased for a spare hub assembly to carry in vehicle for possible bearing or seal failure during fishing trips. Much easier to get back on road versus seal and bearings replacement on road.
Very knowledgeable pleasure to work with
etrailer is a great place, and has excellent sales people who are knowledgeable and patient with folks who don't know quite what they need. Highly recommended.
Product was a great fit, easy to install if you know what you are doing. Took only 10 minutes to repack bearings and assemble.
Though supply chain issues slowed down my original order, etrailer found a suitable substitute, and even saved me some money in the process. I don’t do a lot of work on trailers, but when I do, I know where I’ll be getting my parts.
Used an axle conversion kit to ‘flip’ the axle on my ‘08 Forrest River pop up and give it a lift. Put on the Easy Grease Trailer Idler Hub for 2K Axles - 13" to 15" Wheels - 5 on 4-1/2 - Pre-Greased from etrailer, then switched the 12” stock tires to Contender ST205/75R14 Radial Trailer Tire w/ 14" Silver Mod Wheel - 5 on 4-1/2 - Load Range C to lift it a little more while also putting a sturdier tire on. Works great!
Very pleased with the service and help I received making sure I ordered the correct hub it was very easy to install.
Took forever to ship and still not deli vered
The hubs arrived in a timely manner and were well packaged. Etrailer was great when I contacted them with installation questions. Hubs have been installed for about a year and are working perfectly.
Received parts yesterday and everything arrived in excellent condition. Without etrailer's helpful guides it would have taken a lot longer to identify the correct Hub's and bearing's that I needed for my jet ski trailer. I always go to etrailer for my trailer needs!!!! I have a jet ski trailer, boat trailer, and 36.5 foot 5th wheel camper. So I'm always needing parts!!!
We pack the bearings in these hubs and carry them along for spare, ready to install on the trailer if bearing goes bad while on the road. We use these trailers for trips from northern Indiana to south florida, than to Iowa. Then back to Indiana. So its a lot faster to just change the whole hub when you have trouble.
Perfect fit made for an easy installati on
Excellent kit. Simply take off old hub and slide the new hub on. Comes pre-packed with what appears to be Lubrimax (green) marine grease.
Good product, good price. Jenny B was very helpful and knowledgeable, to ensure I received the correct part. Just what I needed for my enclosed motorcycle trailer.
Great price, good quality. This is the same hube as AKIHUB-545-2-2k, but NOT pre-assembled and pre-greased. Perfect if you want to do this work yourself or need to do work on the hubs prior to usage.
Exactly what I needed and shipped fast and free!!! Pleasure to do business with
Product installed easily and was a good quality hub. changed both hubs. etrailer is the best. Allison was very professional and knew her products.
I don’t know much about this stuff but was given great assistance, got the right stuff and all went great!
Shipped fast great communication rhey have a ton of parts
Haven’t used yet. Products look good and delivery was excellent.
Great job. Great communication
Excellent product and excellent service as always.
Great help figuring out which hub set I needed.
These was perfect! and for sure great quality! Came with everything and took all the guess work out of finding them a piece at a time!
good hubs for the money.
Do you have a question about this Trailer Hubs and Drum?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Jenny N.
10/25/2022
We recently sent you a new hub assembly and were wondering if you had any feedback about the product for other shoppers?