Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/4" Long - 7,500 lbs

See what our Experts say about this CURT Trailer Hitch Ball Mount

• Everything Needed for a 2005 Hyundai Tucson to Tow a Trailer
  You will need five separate parts to tow a trailer with your 2005 Hyundai Tuscon. You will need a trailer hitch, a ballmount, a pin & clip, a hitch ball, and a wiring harness. You have 7 different hitch options for your Tuscon. I would recommend purchasing and installing a hitch with a 2 inch receiver opening over a smaller 1-1/4 inch hitch opening; the larger hitch will give you a lot more options for accessories. Also, we happen to have a very competitively priced Curt Class III Trailer...
  view full answer...
• What Trailer Hitches Will Fit a 2011 Kia Sorento SX
  I have recently spoken to my contact at Draw-Tite regarding Trailer Hitch # 75684. He stated that there are no exclusions for the trailer hitches, except if the vehicle has dual exhaust, which means they should fit all models, including your 2011 Kia Sorento SX unless it has dual exhaust. I have included links to the installation instructions and video. If you plan on doing some towing, the recommended ball mount is # C45010 and you can use ball # 19260 (1-7/8 inch diameter) or # 19247...
  view full answer...
• Trailer Hitch and Accessories for a 2003 Nissan Xterra Towing a Motorcycle Trailer
  Yes, all of our trailer hitches come with the installation mounting hardware. I would recommend the Draw-Tite Xterra Class III Trailer Hitch Receiver, part # 75107. In addition to the trailer hitch, you will need the ball mount, pin and clip or lock, ball and wiring harness. If you have the tow package, you can purchase a wiring harness that will plug right into your factory plug. The Tow Package Vehicle Wiring Harness, Part # 118244. The connection point for the tow package wiring harness...
  view full answer...
• Will the Curt Receiver Hitch # 13354 Fit a 2010 Acura MDX with Factory Spare Tire
  As long as the spare tire under your vehicle is the factory installed spare then the Curt Trailer Hitch, item # 13354, will fit on your vehicle with the spare tire in its original location. The spare will need to be removed to install the hitch but it will be returned to its normal location once the hitch install is complete. I have listed some items you may need to complete your Class III towing setup. Drawbar # C45010 Hitch Ball # 19260 or # 19247 Hitch Lock # e98880 Pin...
  view full answer...
• Recommended Trailer Hitch Receiver and Other Parts to Tow with a 2015 Volvo XC60 T6 R-Design
  I recommend the Draw-Tite receiver, part # 76116, for your 2015 Volvo XC60 T6 R-Design. The R-Design model likely requires you to remove and trim the rear bumper cover but it's still going to fit. I've lined a video that shows the installation but it's not an R-Design so it doesn't show the trimming unfortunately. The recommended ball mount is one with a 2 inch drop and 3/4 inch rise like the Curt # C45010. It fits hitch balls with a 1 inch diameter shank like 2 inch ball # 63845 and...
  view full answer...
• How to Equip 2013 Ford Explorer for Towing 3500 lb Boat and Trailer
  I'd be happy to help with that. The owner's manual states that 3.5L equipped Explorer models can tow up to 5000 lbs 'when properly equipped', but they don't go on to say what 'properly equipped' means. The fact that your vehicle is equipped with the larger engine and the trailer sway feature would leave me to believe your Explorer is properly equipped for towing a boat of your size once the hitch and wiring is added, but I'd recommend checking with your Ford dealer for confirmation. If...
  view full answer...
• Fit of Draw-Tite 76333 on 2021 Subaru Outback XT With Dual Exhaust
  It sure will, and here's why.... The Draw-Tite 76597 which we sell as part # DT94YR doesn't actually install under the vehicle where the exhaust could possibly interfere with the fit of the hitch. The hitch actually installs between the factory bumper/crash beam and the body of the vehicle which is above and rearward of the exhaust. I've linked to an install video showing the hitch being installed on a 2021 Subaru Outback XT like yours. In the video, you can clearly see how the hitch...
  view full answer...
• Fit of Curt Class III Trailer HItch # C13087 on 1999 Toyota 4 Runner
  I have confirmed with Curt Manufacturing that the # C13087 is indeed a fit for your 1999 Toyota 4Runner and that no drilling is required. The hardware uses existing holes to attach the hitch to the vehicle frame. In the unlikely event that you would have some difficulty with the installation, you can give us a call and we would be happy to walk you through the installation. I have linked you to our return policy. You might also need the following to complete your towing set-up. Trailer...
  view full answer...
• What Trailer Hitch Will Fit On A 2007 Grand Caravan With Stow-N-GO Seating
  You will need the Hidden Hitch Trailer Hitch, # 75305, which will work on the 2007 Dodge Caravan with Stow-N-GO seating. It is a Class III hitch and has a towing capacity of 3,500 lbs. with a tongue weight of 350 lbs. On the 2007 Dodge Caravan with Stow-N-GO seating the Hidden Hitch Trailer Hitch, # 75119, that you have referenced will not work. Also needed is a Curt Ball Mount, # C45010, a Pin and Clip, # PC3, and a hitch ball. The hitch ball you need will depends on the size of the...
  view full answer...
• What BallMount Will Fit 2010 Toyota Highlander With 18 Inch Hitch Height To Use On Multiple Trailers
  The standard hitch height that most of the rental trailers are designed for is 17 inches. That will allow the trailer to be towed at the correct level. The hitch height of 18 inches on your 2010 Toyota Highlander is within the standard hitch height. So, if you have a 2-inch receiver the Curt Ball Mount, # C45010, with the 3/4 inch rise and 2 inch drop will work on the majority of the rental trailers. You will also need a Tow Ready Hitch Ball, # 19247, which is a 2 inch ball. The 2 inch...
  view full answer...
• Does Bumper Need To Be Trimmed On Hummer H3 When Installing The Draw-Tite Class III Hitch, # 75382
  There is no cutting or trimming of the bumper on the Hummer H3 when installing the Draw-Tite Class III Trailer Hitch, # 75382. The installation on your Hummer H3 is a very simple bolt-on application. The hardest part might be lowering the exhaust for ease of installation. I am sending a link to the installation instructions for the Draw-Tite Class III Trailer Hitch, # 75382. If you will be towing, you will need the Curt Ball Mount, # C45010, and the Pin and Clip, # PC3. You will also...
  view full answer...
• Will Curt Class III Hitch, # 13530, Fit A 2005 Lexus RX 330 AWD And Is A Converter Box Needed
  The Curt Class III Hitch, # 13530, will fit your 2005 Lexus RX330 AWD. It has a towing weight capacity of 3,500 lbs. and a tongue weight capacity of 350 lbs. The dealer is talking about the wiring harness needed for towing. Because your vehicle has LED tail lamps you do need an upgraded circuit protected taillight converter for the wiring system on your vehicle. It protects your Lexus from electrical shorts and mis-wire situations. I do have the Tow Ready T-One Wiring Harness, # 118478,...
  view full answer...
• What is the Purpose of a Trailer Hitch Ball, Trailer Hitch Pin, and a Clip and are All Necessary
  A hitch ball and a hitch pin and clip each serve a different purpose. A hitch ball, like # 19247, attaches to the ball mount, like # C45010, using a large nut that threads on from the bottom, kind of like a nut and bolt. This ball is what the trailer coupler attaches to. The hitch pin like # PC3 goes through the ball mount and the trailer hitch and the clip keeps it from coming out while traveling. There are also locking hitch pins that use a lock and not a clip like # e98880. Basically,...
  view full answer...
• Will the Curt Hitch # 13328 Fit on a Acura MDX 2004/2005 with Full Size Spare & PDC
  The Curt Class III Trailer Hitch, item # 13328, will fit on both the 2004 and the 2005 models of the Acura MDX. The note about fascia trimming concerns an extra fascia piece that may be installed on some vehicles. If your vehicle rear end looks like the ones in the videos (linked below) no fascia trimming will be needed. The factory sized spare tire will be lowered for installation and reinstalled after installation is complete. I have not seen the park distance control you are referring...
  view full answer...
• Ground Clearance of Curt C13410 Class III Hitches
  That's a great question. We've installed the Curt # C13410 Class III trailer hitches on a 2018 Subaru Outback. We found the Curt hitch offers about 13 inches between the underside of the receiver and the ground. This hitch is a concealed design, with the crossbar concealed behind the vehicle bumper/fascia. The Curt is a great choice for your vehicle. If you'll be towing with the hitch, you'll also need a Tekonsha T-One harness, part # 118467, a ball mount like # C45010 with pin and...
  view full answer...
• Trailer Hitch and Wiring Harness Recommendation for 2018 Subaru Outback
  Although I'd love to sell you the EcoHitch # 306-X7601, the Curt Class III part # C13410 will be just as concealed as the EcoHitch at a lower cost. Curt makes a high quality product that's on par with that of EcoHitch. In this instance you'll sacrifice absolutely nothing by going with the less expensive option. The upside of the EcoHitch is that it is made in the USA and has a mission to recycled materials. Since you'll be towing at some point in the future, there's really no reason not...
  view full answer...
  
• Fit of Curt # 13077 Class III Hitch for 2015 BMW X5
  The fit of the # 13077 does indeed carry over to the 2015 model year of the BMW X5. I have confirmed this with Curt. If you'll be towing with your X5, you might also need the following to complete your towing system: Trailer wiring harness with 4-pole trailer connector, part # 119250KIT Ball mount, part # C45010 1-7/8 inch hitch ball, part # 19620 2 inch hitch ball, part # 63845
  view full answer...
• Can a Trailer Hitch Be Detected by the Back Up Sensors on a 2009 Ford Escape Hybrid
  The available hitches for your 2009 Ford Escape will all extend a little beyond the bumper, but not by much; only about 1 inch. What you can do to test the sensors ahead of time is to place something that extends about 1 inch from the bumper where the hitch would be. If the sensors pick it up, then there is a possibility they will sense the hitch. I would think it is unlikely since the distance is only 1 inch and a steep angle up to the sensors. Even if the hitch did trip the sensors...
  view full answer...
• Is Cutting Or Trimming Required for 2010 Honda Odyssey Trailer Hitch Installation
  The CURT Trailer Hitch, # C13068, for the 2010 Honda Odyssey does have an installation note that states models have underbody fascia covering the driver side frame. This will be removed and can be left off or trimmed and reattached. I have included a link to the installation instructions and a link to a video showing a typical installation for you. Some items you may need to complete your Class III towing setup are listed below. Drawbar # C45010 Hitch Ball # 19260 or # 63845...
  view full answer...
• Which Ball Mount is Best for a 2009 Nissan Murano with a 2 Inch Draw-Tite Hitch
  The smallest drop we have is a 2 inch drop like part # C45010. Letting the trailer ride slightly nose down is acceptable. Nose up or heavily nose down can pose problems. In this case, a 2 inch drop would be the best fit.
  view full answer...
• Tools Necessary For Installing Curt 13417 Class III Hitch on 2020 Ford Ranger
  To install the Curt # C13417 on your 2020 Ford Ranger, you'll need the following tools: 21mm socket Ratchet 6 inch socket extension C-clamp Torque wrench. The installation procedure (see link) is pretty simple. If you'll be towing with the hitch, you'll need a # 22124 wiring harness, a # C45010 ball mount and a # 63851 for a 1-7/8 or # 63845 for a 2 inch trailer ball.
  view full answer...
• Fit of Curt Class III Receiver on 2015 Jeep Grand Cherokee Limited
  According to Curt Manufacturing, their Class III # C13065 is a fit for all 2015 Jeep Grand Cherokee models EXCEPT for Diesel and the SRT-8 models. If you have a Diesel or an SRT-8, the Curt Class III # C13182 is a fit. To complete your system, you might also need a ball mount, part # C45010 and a trailer ball. For a 1-7/8 inch ball, use part # 19260 or part # 63845 for a 2 inch ball. For a trailer wiring harness, use part # C59496. I've linked you to some install videos for the hitches...
  view full answer...
• Trailer Hitch Fit for 2021 GMC Acadia AT4
  According to Draw-Tite, the # 76023 Class III hitch is indeed a fit for the 2021 GMC Acadia AT4. If you'll be using the hitch for towing purposes, you'll also need a few other items to complete your towing system. For a trailer connector, use part # 118720 along with the # C45010 ball mount with pin and clip # PC3 and either the # 19260 1-7/8 inch trailer ball or # 63845 for a 2 inch ball. I've linked to installation videos for the hitch and the trailer wiring harness.
  view full answer...
• Trailer Hitch, Ball Mount, Hitch Ball, and Wiring Recommendations for a 2010 Subaru Forester
  We gauge difficulty of installing a trailer hitch by how long it takes (on average for the every day do-it-yourselfer) to perform the installation. We rate each of the 2 inch hitches for the 2010 Subaru Forester a 4 out of 10, meaning it will take about 40 minutes. All of the 2 inch hitches will require temporary lowering of the exhaust and the widening of a few holes on the frame using a drill (no new holes need to be drilled) to install the hitch. You will also need to fishwire some...
  view full answer...

Do you have a question about this Trailer Hitch Ball Mount?