Customers compare 19286 to these similar products
Products Featured in this Video
What's up everybody It's AJ with etrailer.com. Today, we're gonna be checking out this Draw-Tite "2-5/16" ball. With a weight capacity of 12,000 pounds. Now it also has a diameter down here of the ball of inch and a quarter. So, just make sure you get the right Ball Mount for it to go on. Let's check it out.… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
The replacement parts you are seeking is the Replacement Head and Shank for Reese Weight Distribution Systems - Trunnion Bar #RP54980. This will work with your Reese Strait-Line Weight Distribution System. If you need more drop in the shank, then you…
view full answer...Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…
view full answer...Most of the 2-5/16 inch hitch balls will use either a 1-inch diameter shank or 1-1/4 inch diameter shank. The nut size on a hitch ball with a 1-1/4 inch shank, like the Tow Ready 2-5/16 Inch Hitch Ball, part #19286, will use a 1-7/8 inch socket. A…
view full answer...For that large of a trailer I would almost guarantee it's a 2-5/16 inch hitch ball like the #19286. This ball has a 1-1/4 inch diameter shank and a 12,000 lb capacity.
view full answer...Yes, the range of 900 lbs to 1,500 lbs that you see on the Strait-Line Weight Distribution System #RP66130 that you referenced represents the tongue weight range the spring bars are designed to work on. I attached an FAQ article on determining tongue…
view full answer...Since you have electric stabilizers on your RV you would only use 4 of the arms that come with the part #LC191025. If you check out the install instructions link I attached you can see that your setup is shown in figure 3.
view full answer...In regards to your stabilizer jacks being installed at 45 degree angles, I believe you are referring to telescoping jacks. If they look like what is shown in the accompanying photo then yes, you will be able to use the JT's Strong Arm Jack…
view full answer...There isn't a plug-and-play wiring harness for any brake controller for a 2013 Chevy Silverado, even with the tow package. So while we do have a harness for your Primus brake controller, it is a splice-in harness: - Replacement Brake Control…
view full answer...the wire bundle you are looking for looks like the one in the FAQ article I have linked for you. It is located under the left side of the instrument panel to the left of the steering column. The wiring colors should be as follows: Red/black wire = 12…
view full answer...On the 2008 Chevy Colorado with a factory tow package, the wiring for a brake controller is located under the dash, to the left of the brake pedal. The wire bundle should have a white tag on it that also lists the functions of each wire. You will…
view full answer...It sounds as if the final power connection needs to be made under the hood. If you take a look at the Brake Controller Installation FAQ article I have linked you to, and scroll to the bottom of the page, you can see the procedure for finalizing the…
view full answer...The best way to pick out a weight distribution system is to base it off of the loaded tongue weight of the setup when it is loaded and ready to tow. This figure also includes the weight of any cargo behind the rear axle of the tow vehicle. I attached…
view full answer...