Customers compare D-4 to these similar products
Products Featured in this Video
What's up everybody Adam here with the etrailer, and let's take a look at this curt ball mount. So this one's going to be for your two inch hitch receiver, and it's gonna give us a drop of two inches or a rise of three quarters of an inch. And it does not come with the ball, so pick whatever ball that you need for your trailers and just make sure it's gonna fit through a inch diameter hole down… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
We can only guarantee that the Draw Tite QSP #63080 will work on 2 inch Draw Tite hitches so we can't gaurantee it will fit your 2004 Dodge Durango factory hitch. As long as you have a hollow hitch accessory the #63232 would be a great option…
view full answer...I have a solution for you but the Draw Tite QSP anti rattle item #63080 you referenced can only be used on Draw Tite hitches. For a similar option you will want to use the Hitch Receiver Immobilizer II item #BX88224 which can be used on etrailer…
view full answer...What is probably happening is that the collar around the receiver opening on the Curt hitch has a very thick powder coat that is preventing the Draw-Tite QSP #63080 from fitting properly. If you were to sand away some of the powder coat on the collar…
view full answer...For your 2011 Suzuki Grand Vitara and Curt hitch #C13001 you can use any ball mount rated for a Class III, 2 inch trailer hitch. The recommended ball mount for the hitch and vehicle is #D-4 and it measures 8-1/2 inches from the center of the hitch…
view full answer...In order to get a ball mount that has effectively 0 inches of rise or drop you would need to get a Trailer Hitch Ball Mount, part #D-4, like the one you referenced that has a 2 inch drop, and then use a 2 Inch High Rise Ball, part #C40034. I attached…
view full answer...Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…
view full answer...The Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part #C56217 which is a fit for a 2019 Toyota Highlander has three fuses; 1 ATC, 1 ATS, and 1 Mini. The ATC fuse goes inside the inline fuse holder on the power wire from…
view full answer...If you haven't already, I would start by replacing that fuse. The #C56407 uses a 10 amp fuse. I'm assuming you repaired the short in the wiring as well so I would see if it works after the fuse is replaced. If it still doesn't work, it…
view full answer...This will depend on the hitch used and the height of the trailer coupler. You want the trailer to be as level as possible. We have a page on calculating hitch height and coupler height to help you find what ball mount would work best. Most light duty…
view full answer...To mount one crossbar to your 2021 Toyota Tacoma Double Cab I recommend the Base Line Towers #Y28TR, Round 48" Crossbar #Y8810021, Round Bar Adapter #Y03536, and Base Clip Fit Kit #Y06128 if you are mounting the crossbar on the rear of the…
view full answer...The 12V accessory line on the 7-way connector on your truck which is the pin in the 1 o'clock position when looking at the front of the 7-way, will not charge the battery in your camper. It can maintain the charge of the battery when connected.…
view full answer...I contacted Plews and the only suggestion they can give to remove a stuck cartridge is to try to remove it with a pair of pliers. They also mentioned their grease guns like part #L30100 are not compatible with Mystic grease cartridges. You also want…
view full answer...