Customers compare A35W42B to these similar products
Products Featured in this Video
Today were going to be replacing the wiring on this trailer. We will be replacing a 4 pole flat, as you can tell this one is pretty beat up and worn, so it has to be replaced. We are going to cut this wire off and we are going to replace this brown wire also. We are going to cut this loose and pull the rest of our wire through, on this trailer here it is pretty open so we can reach the wiring.… see more >
Info for these parts were:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
If your Ram has the under-bed heavy-duty towing option, there will be a series of mounting holes or pucks in the bed of your truck, most likely covered by rubber or plastic plugs. If your truck is equipped with the pucks, you can use either an…
view full answer...If the Roadmaster InvisiBrake Supplemental Braking System #RM-8700 brake signal alert was functioning correctly until just recently then the issue is most likely going to be some sort of wiring damage/wear. The ground would be a great place to start…
view full answer...Wiring the grounds for your tail lights and the 35 ft. Wishbone 4-Way Trailer Wiring Harness with 42 inch Ground Wire, item #A35W42B, is fairly simple. The 42 inch ground wire provided with the harness is normally attached to the trailer frame near…
view full answer...While there isn't a life expectancy, per se, of the shocks on the Yakima Rack and Roll Trailer - 66" #Y08106 and 78" #Y08107, upgrading to the HD shocks is absolutely a good idea if your gear weighs around 200 llbs and certainly…
view full answer...I went out to the warehouse and pulled a 35 ft. Wishbone 4-Way Trailer Wiring Harness, #A35W42B, and used a wire gauge tool to measure the wires. The copper wire itself is 20 gauge. If you measure the wire with the insulation on it then it is thicker…
view full answer...It sounds like you have a trailer taillight that grounds through the mounting hardware. Typically the red wire would run to the turn signal/stop light circuit and the black would run to the taillight circuit, and then the ground circuit would be…
view full answer...There are several items you might want to try using for removal of corrosion in your 7-way trailer connector, like part #HM48480. White Vinegar A wedge shaped, slip on pencil eraser or art gum eraser Pipe cleaners PB Blaster If the corrosion is…
view full answer...You can install a 7 way connector on your 2019 Ford F-150 by using the Curt T-Connector #C56413, which will plug into the factory supplied 4 way connector plug on your vehicle and give you a fully functioning 7 way connector. If you've got a…
view full answer...For your 2015 Jeep Patriot, I recommend the Draw-Tite Class III Max Frame Receiver Hitch #75712. This hitch is custom-fit for your Jeep, meaning there will be no drilling required during installation. This hitch will give you a 2 inch receiver…
view full answer...Yakima changed the lights on the Rack and Roll trailers to LED lights in October of 2010 so I can confirm that the replacement marker light, #8880185, is an LED light.
view full answer...It sounds like your trailer had a wishbone harness and/or could have multiple ground wires. On a 4-Way trailer end, the one covered pin is the ground. Next to that is the running light pin. The running light pin on some connectors will have more than…
view full answer...The way that the 35 foot Wishbone 4-Way Trailer Wiring Harness, #A35W42B, works is instead of having 1 taillight wire (brown) that you would need to splice into in order to run to both taillights, this harness has two wires (one attached to each…
view full answer...