Customers compare 8-285-10UC3-A to these similar products
Products Featured in this Video
Hello, everybody, this is Jeff at etrailer.com. Today, we're gonna take a look at the Dexter 12 1/4 inch Trailer Hub and Drum Assembly with the 8 on 6 1/2 inch bolt pattern, has the 5/8 inch wheel studs, and it's for 8,000 pound oil bath axles. Now, this trailer hub and drum assembly is what'll provide the surface area for your brake shoes or your electric magnet to grip when your brakes are… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
The part that you're looking for is the Dexter Trailer Hub and Drum Assembly for 8,000-lb Nev-R-Lube Axles - 8 on 6-1/2 #DX87XR. This is the same as the part #8-385-81SP that you mentioned with the 9/16" studs except the DX87XR has…
view full answer...We have the Dexter Hub and Drum part #8-219-9UC3-A which is a 7k oil bath hub and drum. It would fit your current axle perfectly and allow you to convert it to oil bath.
view full answer...To add oil to the Trailer Hub and Drum Assembly - 8,000-lb Axles - 8 on 6-1/2 - Oil Bath Item #8-285-10UC3-A I recommend using 80w-90 gear oil. The 80w-90 gear oil is what we use on any of our new wet bath hub and drum assembly installs. Unlike…
view full answer...To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…
view full answer...In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
view full answer...Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…
view full answer...Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…
view full answer...I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…
view full answer...Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…
view full answer...There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…
view full answer...I'd be happy to help you out, John! To replace the brakes on your 5th wheel trailer you need the etrailer Electric Trailer Brakes #AKEBRK-7-SA which come with a self-adjusting feature so once you initially set them up you won't have to adjust…
view full answer...The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…
view full answer...