2-1/2 inch to 2 Inch Receiver Adapter to Accept 2 Inch Shank

Question

Question:

is there an adapter made for a 2.5 inch receiver to accept the two inch ball sleeve?

asked by: Cliff

0

Expert Reply:

Yes, we have the Titan Reducer Sleeve 2-1/2 inch to 2 inch, item # C45405. Finally, we have the Diversi-Tech 2-1/2 inch to 2 inch Adapter Kit for DTLBM and DTALBM Series Locking Ball mounts, item # DTADP35, which is designed to work with the Diversi-Tech Aluminum ball mounts and includes a Long-span, locking hitch pin.

expert reply by: Robert G

0

Answer 1

There is a way for you to not only lock the B&W Tow & Stow 3-Ball Mount - Compatible with GM MultiPro Tailgate - 2.5" Hitch - 148K #BWTS20067BMP to your 2-1/2 inch trailer hitch, but also the ball platform to the mount, and the hitch…

view full answer...

Answer 2

Actually the only way to open the BakFlip MX4 is if you have the tailgate open. If you check out the picture I attached you'll see the release cable and that it's under the cover and only accessible with tailgate open.

view full answer...

Answer 3

The BAKFlip MX4 Hard Tonneau Cover part #BAK48120 which is a fit for 2014 - 2018 GMC Sierra/Chevrolet Silverado 1500's with the 5-1/2' bed is very secure. In order to access the release string for the cover you would need access to inside the…

view full answer...

Answer 4

There are a few differences between the BAK Revolver X2 and X4s tonneau covers. The X4s is the newest cover available by BAK, so it includes a new matte black finish on all sides, whereas the X2 will be matte on the top, and then silver on the…

view full answer...

Answer 5

I have a better solution for you than a sleeve adapter. What would be better for you would be a weight distribution shank that is designed for 2-1/2 inch hitches like the #EQ90-02-4800. The great thing about weight distribution shanks is that they…

view full answer...

Answer 6

We have one solution that will work well, but you'll need to have a 2-1/2 inch hitch installed on your tow vehicle. The Brophy hitch extender part #HR26 is a 7 inch extension with a capacity of 10,000 lbs so it would work well.

view full answer...

Answer 7

The sleeve adapters used adapt a 2-1/2 inch hitch to fit a 2 inch hitch accessory do not diminish the towing capacity of the hitch or the accessory installed in the hitch. We have the Curt hitch reducer part #C45405 that would work well for your…

view full answer...

Answer 8

If your Class V receiver has a 2-1/2 inch hitch opening, the best adapter is the Curt Hitch Receiver Reducer Sleeve - 2-1/2" to 2" #C45405 If both the Class IV and V hitches are 2 inches, there is no adapter needed.

view full answer...

Answer 9

The short answer to this question is- No. The B&W Hitch Receiver Reducer Sleeve #BWRHXA2182 does not reduce the tongue weight or towing capacity of your hitch in the same manner that a hitch adapter like the #HTAD would. You will still be able to…

view full answer...

Answer 10

Yes, the Brophy Hitch Reducer and Extender part #HR26 can be used with a weight distribution system but you will be limited to 10,000 lbs or 1/3 of your trailer hitch's weight capacity, whichever is lower. This adapter will provide you with a…

view full answer...

Answer 11

The Curt Hitch Adapter #C45405 will not reduce the tongue weight of your hitch. Many adapters that extend the length will reduce towing capacity based on tongue weight, but this adapter isn't one of them. It will work fine with the Curt TruTrack…

view full answer...

Answer 12

The biggest difference between the Reese Towpower 7028700 and the Curt Reducer Sleeve #C45405 is that the Curt can be used with a weight distribution system while the Towpower comes with a sticker that says it isn't rated for weight distribution.…

view full answer...

2-1/2 inch to 2 Inch Receiver Adapter to Accept 2 Inch Shank

Product Page this Question was Asked From

Continue Researching