Can a Curt Weight Distribution System be Used on a Trailer with I-Beam Frame
Question:
can this hitch be used on a I beam trailer frame on a deck over trailer
asked by: Jerome K
Expert Reply:
You will need to use a standard weight distribution kit like the Heavy Duty Trunnion Weight Distribution System # RP66131 for your I-beam trailer.
To use the Heavy Duty Trunnion Weight Distribution System, # RP66131, or a similar system, you will need to have a steel plate 5 or 6 inches wide welded, by an experienced welder, at 30 inches on center from the center of the hitch ball.
Before modifying the trailer frame you will need to check with the trailer manufacturer to see if this will create an unsafe condition, or void your trailer warranty.
Once the plates are welded on you would then use the bolt on Weight Distribution Chain Hanger Kit, # RP58305 to attach the weight distribution system to the frame.
The system listed above is an example. To choose a weight distribution system you will need to go by the total tongue weight of the set up. This is calculated by taking the tongue weight of the trailer, when loaded and ready to tow, and adding to that the weight of anything loaded behind the rear axle of the tow vehicle. I have included some links that should help.
Products Referenced in This Question
Chain Hangers for Reese Weight Distribution Systems - Bolt On
- Accessories and Parts
- Weight Distribution Hitch
- Chain Hangers
- Reese
more information >
Reese Weight Distribution w/out Shank - Trunnion Bar - 15,000 lbs GTW, 1,500 lbs TW
- Weight Distribution Hitch
- WD Only
- No Sway
- Shank Not Included
- Electric Brake Compatible
- Fits 2 Inch Hitch
- 1100 lbs
- 1200 lbs
- 1300 lbs
- 1400 lbs
- Reese
more information >
Product Page this Question was Asked From
Curt MV Weight Distribution System w/ Friction Sway Control - Round Bar - 14K GTW, 1.4K TW
- Weight Distribution Hitch
- WD With Sway Control
- Some Sway
- Includes Shank
- Electric Brake Compatible
- Fits 2 Inch Hitch
- Does Not Allow Backing Up
- 1100 lbs
- 1200 lbs
- 1300 lbs
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Search Results: weight distribution hitch
- Shop: Reese Pro Round Bar Weight Distribution w Sway Control - Round Bar - 11,500 lbs GTW, 1,150 lbs TW
- Shop: Curt MV Weight Distribution System w/ Friction Sway Control - Round Bar - 14K GTW, 1.4K TW
- Shop: Curt MV Weight Distribution System - Round Bar - 14,000 lbs GTW, 1,400 lbs TW
- Search Results: wdh
- Shop: Suspension Enhancement
- Shop: Brake Controller
- Shop: Trailer Hitch
- Shop: Performance Chip Tuners
- Video: Trailer Brake Controller Installation - 2012 Chevrolet Silverado 90195
- Shop: Air Lift LoadLifter 5000 Air Helper Springs - Rear Axle
- Shop: Superchips Flashpaq F5 Performance Tuner - California Approved - Gas/Diesel
- Shop: Curt Short-Arm Weight Distribution System with Sway Control - Trunnion Bar - 15K GTW, 1.5K TW
- Shop: Curt MV Weight Distribution System - Round Bar - 10,000 lbs GTW, 1,000 lbs TW
- Q&A: Troubleshooting Trailer Brake Controller Won't Turn On When Wired to GMC Sierra
- Q&A: Troubleshooting Blank Screen on Tekonsha Prodigy P3 Brake Controller
- Q&A: Does the P3 Brake Controller Have to Be Connected to a Trailer to Display Voltage
- Q&A: No Power On Brake Light Circuit When Installing a Brake Controller
- Q&A: Distance from Ball to End of Chain Bracket on Curt Short Arm Weight Distribution System # C17333
- Q&A: Recommended Weight Distribution Hitch for 10,000-lbs GVWR Dump Trailer
- Q&A: Confirmation of Proper Wheel Well Height for Older Pro Series Weight Distribution System
- Search Results: ball
- Article: How to Choose the Right Trailer Hitch Class
- Shop: Trailer Wiring
- Video: Choosing the Right Trailer Wiring
- Search Results: 44649
- Search Results: 25580
- Video: Choosing the Right Brake Controller
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Wiring Diagrams