Spring Bar Length for Curt MV Weight Distribution System # C17063

Question

Question:

Could you tell me how long the spring bars are and/or how far from center of ball hitch do I need to mount the lift brackets. This is for item # C17063, Curtis WDH. Thanks

asked by: Todd C

0

Expert Reply:

The round spring bars included in the Curt MV Weight Distribution System # C17063 referenced in your question measure 31.67 inches in length. The lift brackets on this system should be located a minimum of 33 inches from the center of the hitch ball.

This friction sway weight distribution system will do a very nice job of evenly distributing weight over the axles of your trailer and tow vehicle, along with reducing sway caused by winds, passing traffic or sudden maneuvers. The system has a tongue weight capacity of 1,000 to 1,400 pounds. You will want to make sure your total tongue weight, which includes the loaded tongue weight of your trailer along with any added cargo weight coming from behind the rear axle of your tow vehicle, falls somewhere within this range.

I have attached the complete installation instructions and a short video demonstration on this system that you can also check out.

expert reply by: Chris R

0

Answer 1

The brake signal should be fused. Check the vehicle owners manual for the fuse locations for the stop light switch or CHMSL (center high mount stop lamp). If either is blown there would be no power at the plug you found. If you have a Chevy or GMC…

view full answer...

Answer 2

The Draw-Tite I-Stop IQ model 20191 Brake Controller is an older model but it should be compatible with the factory harness on your 2016 GMC Sierra. If the unit isn't powering on at all when wired to the truck then there might be a blown or…

view full answer...

Answer 3

If you are getting a blank screen on your Tekonsha Prodigy P3 Brake Controller #90195 you might just need to reset the unit (as simple as that might sound). Try unplugging the controller, waiting for about 15 minutes, and then plugging it back in.…

view full answer...

Answer 4

In order for the P3 part #90195 to start applying voltage to the brake output circuit the controller has to first detect that a trailer is connected to the tow vehicle. In the video you referenced there was a trailer connected to the truck. Your…

view full answer...

Answer 5

According to the installation instructions for the Pro Series 49902, once the weight distribution system is installed and properly set up, the front wheel well or fender height should be equal or less than what it was before the trailer was hitched…

view full answer...

Answer 6

On Curt weight distribution system #C17333 from the center of the ball cavity in the trailer coupler to the far edge of a chain hanging bracket it is 30-5/8 inches. It sounds like this will work out for you since you are looking for less than 32…

view full answer...

Answer 7

You will need to use a standard weight distribution kit like the Heavy Duty Trunnion Weight Distribution System #RP66131 for your I-beam trailer. To use the Heavy Duty Trunnion Weight Distribution System, #RP66131, or a similar system, you will need…

view full answer...

Answer 8

To my understanding you'll want to use the standard clamp system that comes with the weight distribution system like what we see with the Curt MV #C17063 you were looking at when it comes to an aluminum trailer simply because aluminum frames…

view full answer...

Answer 9

The standard spring bar length for Curt trunnion bar weight distribution systems is 30-5/8 inches. Anything that has 28-3/8 inch long bars is a short bar system even if it does not explicitly state it. What you might be able to do is use chain…

view full answer...

Answer 10

I recommend using the Curt MV Weight Distribution System w/ Friction Sway Control - Round Bar - 14K GTW, 1.4K TW #C17063, which will work well for your 10000-lbs GVWR trailer; you will want to make sure that your trailer does not exceed the 1400-lbs…

view full answer...

Answer 11

I can end this debate for you real fast! Trailer tires, which will have an ST in front of the size, should always be inflated to the maximum psi indicated on the tire. Trailer tires usually do not have a recommended and maximum psi indication so I am…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...