Towing Capacity for the Draw-Tite Max-E-Loader Trailer Hitch Receiver # 75728

Question

Question:

Am I correct to understand that this hitch can not tow a vehicle with a GVW of 4,600 lbs.?

asked by: Chuck

0

Expert Reply:

The towing capacities for the Draw-Tite Max-E-Loader Trailer Hitch Receiver # 75728 are:

Maximum gross trailer weight: 3,500 lbs
Maximum GTW when used with weight distribution: 4,000 lbs
Maximum tongue weight: 525 lbs
Maximum TW when used with weight distribution: 525 lbs

As you can see this hitch would not have the capacity for a trailer that weighs of 4,600 lbs.

expert reply by: Jameson C

0

Answer 1

The Draw-Tite Trailer Hitch Receiver #75728 is for the Ford Edge Sport and will not fit your 2013 Ford Edge SEL. On you SEL model instead you need Draw-Tite #75992. It is designed to fit models with dual exhaust. I've attached a picture of…

view full answer...

Answer 2

As long as the side-view mirrors on your 2013 Ford Edge have a gap between the mirror and the mirror housing, the CIPA Clip-On Universal Towing Mirrors, #7070, will fit. This is a universal mirror that was designed to fit many different mirror…

view full answer...

Answer 3

The best hitch for ground clearance on your 2013 Ford Edge Sport is the Draw Tite part #75728 that you referenced because it has a crosstube that sits above the hitch opening which means that only the hitch tube will hang down. While that may not…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The best way to determine the height needed is to measure from the top of your trailer frame to the top of the sides of your boat. If the 40" Tall Guide-Ons #CE27626 sit right at or slightly above the sides of your boat then the shorter will…

view full answer...

Answer 7

Hey Kevin, for your Demco DA70 actuator you can use the Reverse Lockout Solenoid for Demco Hydraulic Brake Actuators #DM11993.

view full answer...

Answer 8

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 9

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

I have attached a chart you can check out that describes the torque needed per wheel size, wheel stud size and material. For an 8-inch wheel with a 1/2-inch wheel stud the torque is 75 to 86 ft-lbs. For a 15 inch steel wheel with 1/2 inch wheel studs…

view full answer...

Towing Capacity for the Draw-Tite Max-E-Loader Trailer Hitch Receiver # 75728

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching