Recommended Yakima HitchLock

Question

Question:

I am about to purchase Yakima StraightShot Hitch Extension - 2 Hitches - 7-1/4 Long - Y69VR. I would like a lock for the threaded pin that comes with the extension. Is there one available? Thank you

asked by: Jim

0

Expert Reply:

Yes, there is! To add a lock to the Yakima StraightShot Hitch Extension item # Y69VR you will want the Yakima HitchLock item # Y07235.

expert reply by: Jerred H

0

Answer 1

Yes you can use the Yakima StraightShot Hitch Extension #Y69VR with the Yakima EXO systems as well.

view full answer...

Answer 2

I recommend the Brophy Hitch Extender #HE06 with a Stainless Steel Locking, Anti-Rattle Threaded Hitch Pin #SR25219 for your 2016 Hyundai Santa Fe. The Yakima StraightShot #Y69VR does not offer a locking pin that is threaded to match, and the Curt…

view full answer...

Answer 3

Typically when you start using adapters to extend away from the cross tube of your hitch, it gets weaker; in most cases you'll lose around 50% of the tongue weight of the hitch when you use an extension or adapter of any type. If…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 6

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Answer 7

The spacing will depend on the axle diameter and on which particular spring hanger kit you use. If you have a 6000 lb 3 inch diameter axle, and you're using the #APT5 hanger kit which includes 7-3/4 inch equalizers and 2-5/8 inch shackle straps…

view full answer...

Answer 8

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 9

On equalizer 013-105-04 in kit #K71-360-00 the eye center to eye center measurement is approximately 7-1/2 inches.

view full answer...

Answer 10

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

I can definitely help you find the correct replacement hub and bearings for your Dexter P-12 SLR axle, but since part of the serial number was unreadable you will need to take a few simple steps to identify which bearings your axle uses. The easiest…

view full answer...

Recommended Yakima HitchLock

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching