Replacement for Dexter 8-248 Idler Hub

Question

Question:

I have a Dexter axle on my aluma aluminum trailer the order numbers on it are 82582-4 and DEX61031. I am looking for new hubs for it as they appear to be loose and should be replaced as I am traveling cross coumtry with it soon it is an older aluminum 14 foot trailer. the number on the hub is 8-248. what replacement should I use? Thanks Keith

asked by: Keith S

0

Expert Reply:

Hi Keith; the Dexter 8-248 uses standard bearings for a 3,500 lb axle. If you want a hub and drum assembly the # AKHD-545-35-EZ-K you were looking at will fit. The direct Dexter replacement for the idler hub is the # 84545BX or if you want it pre-greased the # 84545UC1-EZ.

expert reply by: Robin H

0

Answer 1

The great thing about Bearing Buddy like part #BB1781 is that when you add grease to your system with the included fitting, it will move the spring-loaded piston outward and allow grease to seep around the edges to keep from damaging the seal. You…

view full answer...

Answer 2

I was able to find the OEM part number for the Chevy spare tire hoist but I was unable to find a weight capacity rating on it. The owner's manual for the 2015 Chevy Silverado 1500 and the original hoist can handle the weight of a full sized spare…

view full answer...

Answer 3

To raise and lower the Lippert Spare Tire Winch with Offset Cable #LC159056 what you need is the replacement manual crank handle part #LC119226.

view full answer...

Answer 4

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 5

The Replacement Crank Extension for Lippert Components Spare Tire Winch Assemblies #LC1315411, which is a replacement for Lippert Components Spare Tire Winch with Offset Cable #LC159056, has an inside diameter of 0.50 inches and the hex has a 0.75…

view full answer...

Answer 6

The Lippert Components Spare Tire Winch with Offset Cable #LC159056 requires the handle #LC119226 to crank up and down.

view full answer...

Answer 7

The Lippert Components Spare Tire Winch with Offset Cable #LC159056 will not have any locking or hold mechanism short of being completely reeled in. I spoke to my tech contact at Lippert who has this on his truck and he said you just crank it up…

view full answer...

Answer 8

It is possible to over-fill a hub that has a Bearing Buddy bearing protector such as #BB1781. The convenience of easy filling through the zerk fitting can often mean we can be tempted to keep adding more grease. ("If a little is good, then more…

view full answer...

Answer 9

The Trailer Hub and Drum Assembly part #AKHD-545-35-EZ-K would be an excellent replacement for a Tru-Ryde Hub/Drum RVD-H-545. Then for new brakes, I recommend the Hydraulic Trailer Brake Kit part #AKFBBRK-35.

view full answer...

Answer 10

The Dexter "8-248" is a hub assembly for 3,500 lb axles that uses an L68149 inner bearing and a L44649 outer bearing. This hub assembly was offered in both 5 on 4-1/2" and 5 on 4-3/4" bolt patterns therefore you would need to…

view full answer...

Answer 11

We have just what you are looking for. I called my contact at TDE and asked about the hub you have on your boat trailer. They told me that it was a 5-stud idler hub for a 3,500-lb axle. That means you need the part #AKIHUB-545-35-K. This is a fit for…

view full answer...

Answer 12

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...