How To Tell If Bearing Buddy Has Enough Grease
Question:
How do know when to add grease to a bearing buddy and how would you know how much you are adding? Thanks.
asked by: Paul Y
Helpful Expert Reply:
The great thing about Bearing Buddy like part # BB1781 is that when you add grease to your system with the included fitting, it will move the spring-loaded piston outward and allow grease to seep around the edges to keep from damaging the seal.
You can manually check the Bearing Buddy to be sure it has enough grease. All you need to do is press the edge of the piston. If you can move or rock the piston it has enough grease. I have attached a drawing of a Bearing Buddy you can check out to see what the components are.
I have attached a link to our product page for Bearing Protectors you can check out. I also attached a helpful article that explains how to replace and install bearings, races, and seals you may want to take a look at.
Product Page this Question was Asked From
Bearing Buddy Bearing Protectors - Model 1781 - Chrome Plated (Pair)
- Trailer Bearings Races Seals Caps
- Caps
- Bearing Protector Grease Cap
- 1.781 Inch
- Bearing Buddy
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Q&A: Can Bearing Buddy Bearing Protectors Be Over-Filled with Too Much Grease
- Q&A: How to Add Grease to Hub that Uses Bearing Buddies
- Q&A: How Does Inner Bearing Get Grease When using Bearing Buddy
- Q&A: When Using Bearing Buddy Bearing Protectors Do I Need To Repack Bearings Periodically?
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Article: Trailer Tire Sizing
- Search Results: 215/60~8
- Shop: Trailer Hitch
- Shop: Kenda 215/60-8 Bias Trailer Tire with 8" Galvanized Wheel - 5 on 4-1/2 - Load Range D
- Search Results: ball mount 7 inch drop
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: Kenda 215/60-8 Bias Trailer Tire with 8" White Wheel - 5 on 4-1/2 - Load Range D
- Shop: Trailer Axle with Idler Hubs - 5 on 4-1/2 Bolt Pattern - 72" Long - 2,000 lbs
- Shop: CE Smith Trailer Idler Hub Assembly w/ Case for 3.5K Axles - 5 on 4-1/2 - Galvanized - Pre-Greased
- Shop: 4-Leaf Double-Eye Spring for 2,000-lb Trailer Axles - 26" Long
- Shop: #84 Spindle for 3,500-lb Trailer Axles - 2" Diameter
- Shop: Trailer Wiring
- Search Results: apubr~10
- Q&A: How To Tell What Size Bearing Buddy Is Needed for My Trailer Hubs
- Q&A: What Causes Grease On the Inside of Boat Trailer Wheels
- Shop: Fifth Wheel Hitch
- Video: Kenda Tires and Wheels - Tire with Wheel - AM3H325 Review
- Search Results: ball mount
- Q&A: Recommendation For Golf Cart Rims For 18.5x8.5-8 Tires
- Article: My Trailer Hitch Doesn't Fit
- Search Results: bearing buddy
- Video: etrailer Trailer Hitch Installation - 2022 Chevrolet Colorado
- Video: Hopkins Multi-Tow Trailer Connector Installation - 2022 Chevrolet Colorado
- Video: Hopkins Trailer Wiring Harness Installation - 2022 Chevrolet Colorado
- Article: How to Measure the Bolt Pattern of a Trailer Wheel
Eddie B.
3/13/2020
If the piston does not seem to move during the greasing, should I keep putting in grease until it does move?