Replacement Recommendation for TDE 46210 Hub

Question

Question:

I have these hubs on my boat trainer. Do you have these in stock? Assume the spindle make no difference.

asked by: Charlie C

0

Expert Reply:

We have just what you are looking for. I called my contact at TDE and asked about the hub you have on your boat trailer. They told me that it was a 5-stud idler hub for a 3,500-lb axle.

That means you need the part # AKIHUB-545-35-K. This is a fit for the standard spindle 3,500 lb dimension that your trailer.

expert reply by: Jameson C

0

Answer 1

There typically aren't any part numbers stamped onto the trailer spindle that can be used for identification. There are however numbers stamped onto the hub most times which can be used for identification. The TDE46210 tells me you have a…

view full answer...

Answer 2

I did some looking and found that the 46210 and 46845 hubs you currently have use the same #L68149 inner bearing and #L44649 outer bearing. However, as we do not carry the Tie Down Engineering Vortex hubs, I cannot say what all will fit them,…

view full answer...

Answer 3

I'll need more info from you though to pick out the correct seal. I need to know the outer diameter of your spindle where the seal rides and the diameter of your hub where the seal slips into. With that info I can pick you out the correct…

view full answer...

Answer 4

There probably are some stainless steel wheel studs out there somewhere but all the ones we have are either zinc-coated steel or painted steel. If you are having a corrosion problem you might want to consider some thread sealant #LT37482. It will…

view full answer...

Answer 5

The "E" measurement is the diameter of the threaded end of the spindle. Assuming that you have the proper castle nut for the spindle and it takes the same bearings as hub #AKIHUB-545-35-K then you can use the hub. This hub uses…

view full answer...

Answer 6

I have an attached photo which illustrates the dimensions of the E-Z Flex Heavy Duty Rubber Suspension System, part #K71-653-00 you inquired about. As you can see on the photo, the distance from the outer mounting hole on the arm of the equalizer…

view full answer...

Answer 7

Since you have a distance of 35 inches between your axles measured on center the EZ Flex you'd want is the part #K71-653-00 which has an axle capacity of up to 8,000 lbs. It will work great on your 3,500 lb axles.

view full answer...

Answer 8

To find the proper replacement equalizer for your horse trailer you will need to take a couple of measurements. Measure from the center of the front hole to the center of the rear hole. Then measure from the center of the top hole down to the…

view full answer...

Answer 9

It is possible that the MORryde Shocking Absorbing Equalizers #MR27ZR and Wet Bolt Kit #MR46ZR you were looking at will fit your 2020 Grand Design Reflection 337RLS, but the only way to be sure will be measuring what is currently installed on your…

view full answer...

Answer 10

The dimensions of the part #K71-652-00 that you referenced are close enough to the dimensions of your current equalizers that they would fit and work well. The overall height is only off by 7/8 of an inch and the A dimension falls within the range…

view full answer...

Answer 11

You have a standard 3500 lb axle, which uses a #84 spindle compatible with a L68149 inner and an L44649 outer bearing. We offer a few replacement #84 spindles with different stub diameters. • For an E-Z lube spindle with a brake flange and a 1-3/4…

view full answer...

Answer 12

The hangers you currently have on your trailer are ones I have run into before. That being said, I spoke with MORryde and the #MR27ZR will still fit your trailer, but there is a modification that will need to be made. You’ll have to trim according…

view full answer...

Replacement Recommendation for TDE 46210 Hub

Product Page this Question was Asked From

Continue Researching