Option For Rubber Bumper For Rear of Trailer

Question

Question:

Do you have a rubber bumper for the rear of a horse trailer? I need one about 36 long +/-, preferably with 4 holes for mounting.

asked by: Larry D

0

Expert Reply:

Hi Larry,

So we have a couple bumpers that may work, though each is 96 inches long. They can be cut to length though, and the difference is their width, as one is 3" wide and the other 4" wide to fit different size bumpers:

- Pre-Drilled Round Rubber Trailer Bumper - 96" Long x 3" Wide # D3-96

- Pre-Drilled Round Rubber Trailer Bumper - 96" Long x 4" Wide # D4-96

expert reply by: Kyle S

0

Answer 1

You can safely use a Straight Tongue Coupler #DM13689-95 or A-Frame Coupler #DM13205-95 with your aluminum trailer frame. The zinc coating on these are not going to have any reaction with the aluminum frame. Do be sure any channels use spacers in the…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 5

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 6

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 7

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

Hi Larry, So we have a couple bumpers that may work, though each is 96 inches long. They can be cut to length though, and the difference is their width, as one is 3" wide and the other 4" wide to fit different size bumpers: - Pre-Drilled…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

The proper replacement inner assembly member for your UFP 34043 would be indeed be the the Dexter #DX99FR which is compatible with disc brakes. The replacement has an electric lock out and has a 7500K capacity and is intended to work with a 2 inch…

view full answer...

Answer 12

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...