Will 20K Pintle Hook C48210 Bolt to B&W Pintle Hook Mounting Plate PMHD14005

Question

Question:

will #C48210 pintle bolt to shank #BWPMHD14005?

asked by: Russ M

0

Expert Reply:

Yes, you can bolt pintle hook # C48210 to B&W Pintle Hook Mounting Plate # BWPMHD14005. However, the capacity of the mounting plate is 16,000 pounds so that is the maximum capacity of this set up even though the pintle hook is rated higher. You always have to go by the lowest rated component.

expert reply by: Michael H

0

Answer 1

Yes the B&W Pintle Hook Mounting Plate #BWPMHD14005 can absolutely be used in the rise position to raise the height of your pintle hook. This mounting plate fits 2" hitches, has a 15" shank and mounting holes that measure 3-3/8"…

view full answer...

Answer 2

If you have a 2 inch receiver opening on the vehicle you will be towing with the B&W Pintle Hook Mounting Plate, part #BWPMHD14005 may work well for you. The mounting plate features 7 holes on each side of the plate that are spaced 1-3/4 inches…

view full answer...

Answer 3

Yes the Curt Pintle Hook #C48215 will bolt up perfectly to the B&W Pintle Hook Mounting Plate for 2" Hitches #BWPMHD14005 you were looking at. This will give you 6 different positions to mount the pintle hook so you can make sure your…

view full answer...

Answer 4

You are pretty well balanced but given that the axles are the fulcrum (if you think of the trailer as a teeter totter) you have more weight on the long side. If you swap the positions of the Arctic Cat and the Honda/Timberwolf it would be a better…

view full answer...

Answer 5

Yes, the B&W Pintle Hook Mounting Plate part #BWPMHD14005 and the Buyers Products 8 Ton Combination Hitch with Mounting Kit part #33710055 will work with one another as they both have mounting holes spaced 1-3/4" apart on center vertically…

view full answer...

Answer 6

The B&W Pintle Hook Mounting Plate part #BWPMHD14005 that you referenced will slide into a 2" receiver tube opening on the tow vehicle. This will then accept a pintle hook so that you can tow a trailer with a lunette ring, not the other way…

view full answer...

Answer 7

For your 2006 Jeep Liberty Renegade, I recommend using the Convert-A-Ball Pintle Hook Combo with 3 Stainless Steel Balls - Bolt On - 25,000 lbs #PH1. This will give you all 3 of the hitch ball sizes and also give you the pintle hook option. For the…

view full answer...

Answer 8

There's no reason you couldn't use the B&W Pintle Hook Mounting Plate #BWPMHD14005 in both the rise and drop configuration. For a pintle hook to go along with it you might also be interested in the Pintle Hook part #C48210.

view full answer...

Answer 9

As you obviously have already learned there are a lot of variables into building a trailer. And I can't tell you what is or isn't completely safe in your exact circumstances. I highly recommend having your setup evaluated by a professional…

view full answer...

Answer 10

Pintle hitches are made to fit certain sized Lunette rings. The rings that we carry are only available in 2-1/2" or 3" diameter sizes. For example, the Curt Pintle Hook for 2" Hitches #C48004 fits lunette ring couplers with a minimum…

view full answer...

Answer 11

I went to our warehouse and measured the B&W Pintle Hook Mounting Plate #BWPMHD14005. I measured the center to center horizontal hole spacing at 3-3/8-inches so it will work well with Pintle Hook #C48210.

view full answer...

Answer 12

In order to run dual wheels and tires on a 6K axle what we have is the Dexter Trailer Hub and Drum Assembly part #8-219-18UC3 which uses 5/8" lug studs and has a 4.75" pilot. This will then work with the Dexstar Dual Wheel with Offset part…

view full answer...