Mounting Hole Spacing on B&W Pintle Hook Mounting Plate BWPMHD14005

Question

Question:

what pintle hitch will bolt to mount plate #bwpm14005? info says C48210 will work but horizontal holes distances are not right 3 1/2 inchesplate as per 3 3/8 inches hitch. thanks

asked by: Herman

0

Expert Reply:

I went to our warehouse and measured the B&W Pintle Hook Mounting Plate # BWPMHD14005.

I measured the center to center horizontal hole spacing at 3-3/8-inches so it will work well with Pintle Hook # C48210.

expert reply by: Adam R

0

Answer 1

Yes, you can bolt pintle hook #C48210 to B&W Pintle Hook Mounting Plate #BWPMHD14005. However, the capacity of the mounting plate is 16,000 pounds so that is the maximum capacity of this set up even though the pintle hook is rated higher. You…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 8

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 11

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 12

Yes the Curt hitch part #C12130 is a confirmed fit for your 2008 Mercury Marquis. Then for trailer wiring the Curt harness part #C59236 would be a great option. It's a universal style harness that will require hardwiring to the taillight wiring.

view full answer...

Mounting Hole Spacing on B&W Pintle Hook Mounting Plate BWPMHD14005

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching