Can the Demco Hijacker 5th Wheel Hitch Be Used W/ a 2014 Chevrolet Silverado 2500 W/ OEM Pucks

Question

Question:

I have a Demco DM8550037 5th wheel hitch now . And just bought a new truck that has the OEM puck style , How and what do I need to make this work with that style system ?

asked by: Nick B

0

Expert Reply:

Hey Nick, so it looks like the only way you're going to be able to use your Demco Autoslide 5th Wheel Trailer Hitch w/ Slider # DM8550037 with your 2014 Chevy Silverado is by using the custom underbed mounting kit # DM8551010.

This is one of the few hitches that does not use ISR or an OEM puck system to install so you'd have to use their install kit.

expert reply by: Bryce D

0

Nick

3/19/2024

Sorry my new truck is a 19’ gmc 3500hd with the puck system

Reply

Bryce D.

3/19/2024

@Nick Unfortunately that doesn't change anything. Since the Hijacker requires the underbed mounting kit, the only way you'd be able to use this hitch is if you were to uninstall your pucks and install the kit for this hitch specifically.

Reply

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 3

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from…

view full answer...

Answer 4

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 5

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 6

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from…

view full answer...

Answer 7

The total weight of the PullRite OEX SuperLite 5th-Wheel Hitch for Ram Prep Package(4815) #PUL56ZR is 143lbs. The Head #PUL99ZR weighs 49lbs while the Base #PUL56ZR weighs 94lbs. While we do not carry the 2600 currently(5/15/2024) it has a total…

view full answer...

Answer 8

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This…

view full answer...

Answer 9

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 10

Hey Jay. It sounds like you are on the right track here because a sidewinder pin box will be your only option for pulling your 5th wheel since you have a short bed truck with the Rambox. That said, you are right that the Reese Sidewinder cannot be…

view full answer...

Answer 11

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Answer 12

The Gen-Y Hitch 5th Wheel to Gooseneck Pin Box part #GY58GR is primarily designed for long bed trucks. It's no different than a standard fifth wheel pin box in regards to the size. If you were using a fixed hitch and standard pin box before with…

view full answer...