Trailer Hitch Recevier Fit For 2024 Toyota Tundra Without Factory Hitch

Question

Question:

what trailer hitch receiver fits the 2024 toyota tundra without a factory hitch?

asked by: Terry C

0

Expert Reply:

The correct trailer hitch receiver for your 2024 Toyota Tundra without a factory hitch is the following:

- Curt Trailer Hitch Receiver # C44BR

I verified this fit directly with the manufacturer for you.

expert reply by: Kyle S

0

Answer 1

The Curt Hitch item #C44BR has a 12,000 lbs towing capacity and a 1,200 lbs maximum tongue weight. This hitch is custom fit for the 2024 Toyota Tundra's that came from the factory without a hitch. This is a class IV hitch with a 2" receiver.…

view full answer...

Answer 2

It does; so long as your 2023 Toyota Tundra SR long bed does NOT have the factory hitch, the Curt hitch will definitely fit. The correct part number is the following: - Curt Trailer Hitch Receiver #C44BR

view full answer...

Answer 3

Yes, we do have the parts you will need to add all the parts you need on your 2022 Toyota Tundra for towing. First you will need the Curt Trailer Hitch Receiver #C44BR. This is a custom fit receiver with a 2" receiver tube. For the electrical…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 8

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 9

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...