Will Brophy Camper Tie-Downs Fit A 2016 Nissan Frontier SV

Question

Question:

Can I use brophy mounts to mount my Hallmark slide in camper and use in an off road scenario? This whole be going on a 2022 Nissan Frontier SV. Thanks!

asked by: Ryan R

0

Expert Reply:

You'll need to take a few measurements to ensure that the Brophy Clamp On Camper Tie-Downs # HSWB will work with your bedrails. You'll need a minimum of 2" of space between the inner lip of the bedrail to the inner wall (pictured below). If you do have enough space for these to fit then you'll also want to pick up some turnbuckles to complete your setup # TDHP. Brophy doesn't have any listed stipulations on off-roading but I wouldn't recommend really rough terrain because you'll place a lot of strain on the turnbuckles.

expert reply by: Kevin C

0

Brophy Fitment Requirements
(click to enlarge)

Answer 1

According to CR Brophy, the camper tie down brackets you'd looked at, part #HSWB are specifically designed to fit the bed of a 2019 Ford F-250 and 350. There does indeed need to be 2 inches of available space under the lip of the truck bed side…

view full answer...

Answer 2

I spoke with my contact at Brophy and they stated you'll be fine using the Brophy Clamp On Camper Tie-Downs - Bed Mount - Black Powder Coated Steel - Qty 4 Item #HSWB as long as the railing on the back of your 2008 Chevy Silverado isn't over…

view full answer...

Answer 3

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 4

The support braces in the HappiJac Truck-Mounted Camper Tie-Downs #LC182860 are going to attach to the cross frame to provide support for the anchors which will bolt through the bed wall and into the braces. The rear anchors will bolt through the…

view full answer...

Answer 5

The primary advantage of frame-mounted camper tie-downs like the TorkLift #TLF2012A and #TLF3001A, which are designed to fit your Ford F-350 if it has the 6-3/4 foot bed without a step/board underneath and a factory hitch, is the stability they…

view full answer...

Answer 6

Your slide-in truck camper does not have electric brakes so the blue brake circuit wire from its 7-way connector is not used. All other lighting functions as well as 12V auxiliary power will be maintained on the other circuits. Please refer to the…

view full answer...

Answer 7

You do not need to remove the bed of your truck to install the HappiJac part #LC182906-182971 that you referenced. I found a copy of the install instructions for this part number (see attached pictures) and there's no mention of the bed needing…

view full answer...

Answer 8

According to TorkLift's fitment guide the TorkLift Talon Custom Frame-Mounted Camper Tie-Downs #TLF2021A you were looking at are compatible with any factory installed running boards, including ones that extend under the bed so these would be a…

view full answer...

Answer 9

You will need the Front #TLF2021A and Rear #TLF3008A TorkLift Talon Camper Tie-Downs for your 2024 Ford F-350 long bed dually. These are designed to fit as long as you do not have a step below you truck bed and the factory receiver. I recommend…

view full answer...

Answer 10

Hey Brian, so according to TorkLift they don't have any tie downs for the front but for the rear you are going to want the TorkLift Camper Tie-Downs #TL54FR. Since your truck has factory running boards that extend under the bed, there aren't…

view full answer...

Answer 11

Yes, it will! The Hellwig Adjustable Big Wig Rear Anti-Sway Bar item #HE96XR is confirmed to fit your 2024 Chevy Silverado 3500. This sway bar will minimize lateral movement in your rear end and improve stability. This sway bar is made in the USA and…

view full answer...

Answer 12

Yes, we offer replacement hitch install hardware with the part #RHK. You'd simply need to enter the part number of the hitch you have (31320) and then select Curt as the manufacturer and we'd ship you out the correct hardware.

view full answer...