Replacement Cover for Titan BrakeRite Electric Over Hydraulic Actuator 48131

Question

Question:

Does the replacement cover, part no. T4813100 fit my model?

asked by: Ron W

0

Expert Reply:

Part # T4813102 is not a replacement cover, it is a complete BrakeRite actuator Kit. The replacement cover is actually # T4813000. All Titan BrakeRite systems have a 7 digit model number. You mentioned 48131 which is probably supposed to be 4813102 which is one of the models the replacement cover fits.

expert reply by: Michael H

0

Answer 1

It could be that your reverse lockout solenoid needs replacement. Part #T4748800 is the replacement part. But I suspect your master cylinder is the cause for the brakes staying locked up until you release the pressure from the bleed valve on one of…

view full answer...

Answer 2

According to Titan, if only the white and black wires are connected, the hydraulic pump should not run. With those two wires attached, the pump should start when the blue wire is touched to the positive battery terminal. The folks at Titan tell me…

view full answer...

Answer 3

I am sorry to hear you are having an issue with your Dexter DX Series Electric Over Hydraulic Brake Actuator for Drum Brakes - 1,000 psi #K71-650. When I reached out to Dexter and they had a few thoughts. First is to make sure that the drum brakes…

view full answer...

Answer 4

I spoke with my contact at Titan to confirm the operation of the Titan BrakeRite EHB Electric-Hydraulic Actuator for Disc Brakes System, #T4813102, and you are correct that if the BrakeRite is connected to a dead battery, it will bring the system…

view full answer...

Answer 5

I was unable to find a reference to part 4814400 so I assume you were referring to the Titan BrakeRite Electric-Hydraulic Actuator #T4813102 . I contacted Titan who told me it was possible it burned the pump if it ran for a time and you should look…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Thank you for the pictures! For a replacement option I recommend the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout - Bolt On - Disc - 2" Ball - Zinc - 7.5K #DX29FR to replace your current actuator. The #DX29FR has a 7500lb trailer weight…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

You're correct. The repalcement for your existing B12EA-22 brake would be #AKEBRK-7R-SA for the right side and #AKEBRK-7L-SA for the left.

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

The Hydrastar Vented Marine Electric Over Hydraulic Actuator for Disc Brakes #HS481-8067 is designed to be completely plug-and-play so the female end of the 7-way would need to connect to the 7-way cable that's already installed on the trailer…

view full answer...

Answer 12

The HydraStar Marine Electric Over Hydraulic Actuator w/ Breakaway and 7-Way RV Harness #HS381-9067 is designed to work with an aftermarket electric over hydraulic brake controller. This kit will require you to wire in the components using the wire…

view full answer...