Availability of a 7,000LB Trailer Axle With 4" Drop 95" Hub Face and 78" Spring Center

Question

Question:

I was wondering if you could match this axel? PJtrailer 110440- 95x78 4 drop 7k axle

asked by: Les S

0

Expert Reply:

It sounds like the Dexter Trailer Axle Beam # 8327860 is going to be the closest to what you are looking for. This is a 7,000LB underslung trailer axle with a 4" drop. The hub face measurement is the same 95" with a spring center of 79-1/4". You can have new Spring Seats # TRSS300 welded in place at the 78" measurement.

We also have the above axle with electric brakes and hubs # 8327860-EB if you need them as well.

expert reply by: Bud M

0

Answer 1

I just heard back from Dexter and they gave me some information on your axle. I have a solution for you and it is very close to your specifications but you will need to have the spring seats moved. The Dexter Trailer Axle Beam with 4" Drop E-Z…

view full answer...

Answer 2

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 3

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 4

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 5

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 6

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 7

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 10

My contact at Yates Rubber advises that a nominal 8-inch keel roller does not measure exactly 8 inches; typically they are slightly smaller than the specified size, much the way a piece of 2 x 4 lumber is not exactly 2-inches by 4-inches. I took…

view full answer...

Answer 11

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...