Does Dexter Offer a Replacement Control Module For the BrakeRite EOH Trailer Brake Actuator?

Question

Question:

Is the old version SD control module available by itself ? My pump will turn on when the breakaway is pulled but not when using the tow vehicle brake. Was working fine before. Verified power is being sent to the control module but not coming out to motor. Appears to be an issue with the control module.

asked by: Michael M

1

Helpful Expert Reply:

Dexter does not offer a replacement control board for their BrakeRite SD. You will need to upgrade to the Dexter BrakeRite II SD # T4813102 which is plug and play for disc brakes.

expert reply by: Bud M

1

Answer 1

The issue that you are seeing may indeed be an electrical issue. I recommend checking all the connections and wiring and make sure that there are not any loose connections, or signs of damage to any of the wiring. I have included a link to the…

view full answer...

Answer 2

Good news, I can help you troubleshoot your Titan BrakeRite SD #T4835700 on your trailer. First thing to know is that a braking system is necessary when pulling a trailer equipped with brakes. The BrakeRite SD system is a good system for Electric…

view full answer...

Answer 3

Yes, the Replacement Plug and Play Electric-Over-Hydraulic Actuator #DX36XR is the correct part for your Dexter BrakeRite II SD. To replace the wiring harness you also need part #T4834300. This is the harness with the 7-Way connectors and the…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 10

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...