Can Dutton-Lainson Boat Trailer Roller Bunks be Attach to Swivel Brackets

Question

Question:

My bunk boards have swivel brackets flat boards .Can the DL21741 be mounted to these brackets insread of the boards?

asked by: Rot S

0

Expert Reply:

Yes, you can attach the roller bunks # DL21741 to swivel brackets. The brackets will not be able to swivel independently of one another though once attached to a rigid item like the frame of the roller bunks. The brackets that are associated with these roller bunks are # DL21742, and they too have limited swivel abilities so using this type of bracket will work just fine.

expert reply by: Michael H

0

Answer 1

The motors of the Ultra-Fab #UF17-943010 landing gear are encased in plastic covers to keep moisture out, so they can be exposed to weather but they're not meant to be immersed in water. They'll be fine if exposed to splashing and the…

view full answer...

Answer 2

The Ultra-Fab Deluxe Electric Landing Gear Set #UF17-943010 that you referenced is weather proof enough that as long as you didn't submerge the landing gear underwater the jacks would be just fine. Rain and snow wouldn't be an issue…

view full answer...

Answer 3

I would place the roller bunks in the same orientation as the wood bunks that were there previous. There would be no need to extend them out further. Normally the bunks extend just a bit past the rear of the trailer frame like the picture I…

view full answer...

Answer 4

The CE Smith Roller Bunks part #CE27710 that you referenced are made in the USA.

view full answer...

Answer 5

We have roller bunk brackets like the part #DL21742 which have a swivel on the top of them which can angle of the hull with bunks like the part #DL21740. I attached a picture that shows the rollers being used on a boat with an angled hull.

view full answer...

Answer 6

The Kodiak Oil Cap #KPCAP you are looking at is a replacement cap for the Kodiak Pro Lube Kit. The oil cap you need is the Redline Oil Cap, Plug and O-Ring for Dexter 7-9K Trailer Axles #RG04-230. This will replace the oil cap on your trailer axles…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

The best option for a Class C motorhome windsheild cover is going to be the Adco Deluxe Cover part #290-2507 which is designed for Class C motorhomes just like yours. I attached a review video for this cover for you to check out as well.

view full answer...

Answer 10

The Dexter 10K electric brakes #23-439 (right side) and #23-438 (left side) will have to be manually adjusted using the adjustment wheel below the magnet. To adjust the brakes you will use a small screwdriver or similar tool to turn the adjustment…

view full answer...

Answer 11

Yes, the Bolt Trailer Hitch Lock part #BL7023582 will work for you as it is a hitch lock designed for 2-1/2 inch hitches like what you have on your GMC 3500 truck. The usable portion of this lock is 3.55 inches. Check out the picture I attached for…

view full answer...

Answer 12

I checked directly with BOLT for you, and they confirmed for me that your 2021 Chevy Silverado is absolutely compatible with their trailer hitch locks. Take a look at the accompanying photo, and if you have the same center cut key, the correct lock…

view full answer...

Can Dutton-Lainson Boat Trailer Roller Bunks be Attach to Swivel Brackets

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching