Will Trailer Idler Hub Assembly # AKIHUB-5475-35-K Fit 1-3/8" Spindle

Question

Question:

Will it fit 1 3/8 in spindle

asked by: Billy B

0

Expert Reply:

No, the Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-3/4 - Pre-Greased # AKIHUB-5475-35-K only fits a spindle that uses inner bearing L68149 (1.378" inner diameter) and outer bearingL44649 (1.063" inner diameter).

expert reply by: Kyle S

0

Answer 1

When installing your Easy Grease Trailer Idler Hub Assembly for 2K Axles - 4 on 4 - Pre-Greased #AKIHUB-440-2-EZ-1K there should not be any "play" or space. Since it is pre-greased, more grease is not needed. I recommend checking your…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 5

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 11

I have attached for you below some common torque values needed for a trailer suspension system but a lot of these will vary by bolt size and other factors. U-Bolts: Varies by Size - 1/2" bolts: 45 ft/lbs - 70 ft/lbs, 9/16" bolts: 65 ft/lbs…

view full answer...

Answer 12

Since Grand Design is kind enough to list certain parts for their trailers I can confirm you have a 33" wheelbase on your 2020 Grand Design Transcend 27BHS. This means the MORryde Rubber Equalizers #MR87ZR will fit your trailer. Although I'm…

view full answer...

Will Trailer Idler Hub Assembly # AKIHUB-5475-35-K Fit 1-3/8" Spindle

Product Page this Question was Asked From

Continue Researching