Hopkins Trailer Wiring Harness Recommendation for 2010 Lexus ES 350

Question

Question:

I have bought many Curt and Hopkins hitches and wiring harnesses over the years. I recently acquired a 2010 Lexus ES350 car. Could you please recommend which Curt / Hopkins / other make product number would be the correct vehicle specific kit for a 4-pin trailer wiring harness for a 2010 Lexus ES350 car? Thank you.

asked by: Colin S

0

Expert Reply:

Hopkins has a custom fit trailer wiring harness that fits your 2010 Lexus ES 350 with the part # HM11141930. This installs by plugging inline with your taillight connectors so it's a pretty simple install as well.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 5

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 6

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 9

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 10

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 11

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...