Size Nut on B and W Pintle Ball BWTS10051

Question

Question:

What size is the nut on these replacement balls?

asked by: Jake

0

Expert Reply:

The size wrench/socket for the nut of the B and W Pintle Ball # BWTS10051 would be a 1-7/8 inch size.

expert reply by: Jameson C

0

Answer 1

When it comes to the recommend torque specs for the four bolts on The Curt Pintle Hook with 2-5/16 inch Hitch Ball #C48200 per Curt you will need to tighten all the bolts to 90 ft. lbs. The pintle hook has a bolt-on installation to Pintle Hook…

view full answer...

Answer 2

The B&W ball mount #BWBMHD30012 requires a ball with a 1-1/4 inch diameter shank. Ball #BWTS10051 does indeed have a 1-1/4 inch shank so it can be inserted in the ball mount. However it was designed as a replacement for a pintle/ball combo hitch…

view full answer...

Answer 3

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 4

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 5

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

You can get a new brake mounting flange for your axle. The old flange will need to be cut off. The part is #4-44-1. This is designed to fit a 3 inch trailer axle and should be welded in place by a professional. Since you would also have to get the…

view full answer...

Answer 8

We do carry electric brake assemblies as well as hub/drum assemblies. To determine the correct fit, you will need to measure the spindles of your axles. I've attached a photo to assist with the measurement locations, and recommend using a digital…

view full answer...

Answer 9

We do have 205/75R14 size radial tires that have a load range of D and a speed rating of at least 81 mph. Out of our available selection I recommend going with the Kenda Karrier #AM10235. This tire has a max load rating of 2,200 lbs at 75 psi and a…

view full answer...

Answer 10

In regards to the Correct Track Trailer Alignment and Lift Kit part #RR23QX, the kit provides a lift by essentially extending the hangers. This normally requires cutting off the old hangers and welding on new, taller ones but with this kit you…

view full answer...

Answer 11

The Correct Track Trailer Alignment and Lift Kit - Tandem Axle #RR23QX does come with all of the components needed to lift a tandem axle trailer. The center hangers of a tandem axle setup use different components than the front and rear hangers since…

view full answer...

Answer 12

The Correct Track Trailer Alignment and Lift Kit part #RR23QX offers a 1-1/4" or 2-1/4"lift so if the hitch height height is lower than the vehicle hitch height you can use this kit to bring the trailer level with the vehicle and eliminate…

view full answer...

Size Nut on B and W Pintle Ball BWTS10051

Product Page this Question was Asked From

Continue Researching