Ball Mount for 3 inch Trailer Hitch Similar to B and W BWBMHD30012

Question

Question:

Do you have something just like this but with a 3 tongue width? BWBMHD30012

asked by: Robert C

0

Expert Reply:

We have ball mounts similar to the B and W part # BWBMHD30012 that you referenced that fit a 3 inch hitch like the Buyers Products part # BP27FR which has a 2-1/2 inch rise and 4 inch drop.

expert reply by: Jameson C

0

Answer 1

The B&W ball mount #BWBMHD30010 is made in the USA. This one is 8-1/2 inches long but there is a longer one, #BWBMHD30011, which is 10-1/4 inches long.

view full answer...

Answer 2

To select the correct ball mount that will allow you to tow level, you must take two measurements into consideration. First, measure from the ground (on level ground) to the top inside portion of your square hitch receiver opening. Second, measure…

view full answer...

Answer 3

The Curt #C45312 and the B&W #BWBMHD30011 ball mount are wholly manufactured in the USA. Both ball mounts feature a 2 inch drop or a 1 inch rise if inverted. The B&W has a 16K capacity, with the Curt model having a 12K capacity. Both…

view full answer...

Answer 4

The Draw-Tite Ball Mount, #4285, does not include a gusset welded between the shank and platform. Basically, it is not needed. This ball mount is constructed of solid steel. The shank is solid with the only hole in it for the hitch pin. It is welded…

view full answer...

Answer 5

The B&W ball mount #BWBMHD30012 requires a ball with a 1-1/4 inch diameter shank. Ball #BWTS10051 does indeed have a 1-1/4 inch shank so it can be inserted in the ball mount. However it was designed as a replacement for a pintle/ball combo hitch…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

All of the ball mounts we offer for the Class V 2-1/2 inch receiver have the same 10 inch ball hole to pin hole distance you mentioned. This being said, I might have a solution for you. You can use a reducer sleeve like part #C45405 along with a ball…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 12

Hey HPA, I would go with the Air Lift kit part #AL64VJ that fits your 2019 Toyota RAV4 based on what you described and your needs. This gives you adjustable support that you can tailor as needed so that you get the exact amount of support you need…

view full answer...