Does the Curt 5th Wheel Wiring # C56000 Fit a 2014 Chevy Silverado?

Question

Question:

I have 2014 Chevy 2500HD will this fit it?? It is a crew cab. Do you need anything else?

asked by: Ray M

0

Expert Reply:

I checked with Curt and the Curt 5th Wheel/Gooseneck Wiring Harness 7-Pole # C56000 that you referenced is confirmed to work on your 2014 Chevy 2500HD crew cab.

Only thing else you would need is the tools required to complete the install. For that you would need a 3/32 and 1/4 inch drill bit, a 2 inch hole saw, a Philips head screwdriver and center punch.

I attached installation instructions for you to check out.

expert reply by: Jameson C

0

Answer 1

Good morning. Both the #C60720 and the #C60720-5W are the same exact item. We give them different part numbers so that the item can be searched as both a gooseneck hitch and as a mount for the Demco Recon 5th wheel hitch, Both kits include the rails,…

view full answer...

Answer 2

For Curt Double Lock, Flip and Store Underbed Gooseneck Hitch w/Installation Kit - 30,000 lbs Item #C60720 the exhaust does not have to be lowered on a 2001 Ford F-250 diesel for installation. On 2004 and older trucks, the emergency brake cable…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 5

The proper replacement inner assembly member for your UFP 34043 would be indeed be the the Dexter #DX99FR which is compatible with disc brakes. The replacement has an electric lock out and has a 7500K capacity and is intended to work with a 2 inch…

view full answer...

Answer 6

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 7

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 8

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 11

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 12

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...