Replacement Landing Gear Motor For 2006 Coachmen Somerset 358 5th Wheel Camper

Question

Question:

I have a 2006 coachmen Somerset model 358 I am looking to replace the motor for the landing gear wondering if this would fit my fifth wheel camper?

asked by: Roger T

0

Expert Reply:

To find the correct motor for your landing gear on your 2006 Coachmen Somerset 358 5th wheel you will need to check the motor for its part number. We have the Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor # LC141893, Replacement Motor for Stromberg Carlson Electric Landing Gear # LG-142178 and Lippert HD 6500-lbTuson 5th Wheel RV Landing Gear Motor # LC196308. The part number in the manufacturer label will help to identify the correct motor. If you have a different part number on your motor let me know what you have and I will ensure the correct motor for your landing gear.

expert reply by: Bud M

0

Answer 1

The Atwood motor 71113 has been discontinued. The motor is a basic landing gear motor and we've been able to confirm the Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor #LC141893 is the correct replacement. I've…

view full answer...

Answer 2

We do not have those parts available. I checked the parts list for the Ground Control 3.0 Electric Leveling System #LC358590 (4-Point Set) or #LC675817 (6-Point Set) and the inner tube parts are not available by themselves. If you need a…

view full answer...

Answer 3

Any powered landing gear or powered tongue jack will draw less power as it legs descend down toward the ground and much more as soon as they make contact and encounter resistance. This is a normal occurrence. In the same way, any jack - even a…

view full answer...

Answer 4

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 5

We do have the correct replacement for your Atwood 71119 landing gear motor, which is what is shown in your photo. The replacement part is the Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor #LC141893. I have added a link to a…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 10

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 11

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the hitch height…

view full answer...

Answer 12

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...