Troubleshooting Landing Gear Not Lifting 5th Wheel

Question

Question:

I have a 2010 Grand Junction 340RL, Unloaded weight is advertised as 12417 with a hitch weight of 2528. I dont know the weight on the landing gear. I have seen several posts about this problem. The landing gear will operate until the feet hit the ground and puts a load on the landing gear. The fuse pops or the wiring melts. I have to use hydraulic jacks to raise and lower my trailer. I have the LIppert system with the wireless remote control. The motor is the model 1-065-041012-01. The label on the motor says 3.1A. This seems to be incorrect. A 3A motor shouldnt be popping a 30A fuse. I see you recommend the 141893 motor as a replacement. I am considering replacing the entire system with a LG3 or LG4 I do not know the measurements at this time. I know the motor and possible gear replacement would be a cheaper short term fix, but would you recommend a total replacement with a 6,500 lb. system instead? They seem to build these trailers with minimal components. I want something that will do the job reliably. Thanks.

asked by: Steve B

0

Expert Reply:

Any powered landing gear or powered tongue jack will draw less power as it legs descend down toward the ground and much more as soon as they make contact and encounter resistance. This is a normal occurrence. In the same way, any jack - even a manual hand-crank type - requires less power (or force) when lowering the trailer than when lifting it.

The cause for your powered landing gear losing steam could be any of several possibilities. These include the trailer's battery not being rated high enough for the amperage demands from the landing gear (or from the battery being past its best days or not being fully charged before you make a trip); it could be from a corroded or loose ground connection either at the battery end or at the landing gear; it could be from the actual weight of the loaded trailer exceeding the capacity of the OEM jacks. RV makers tend to use less than the beefiest available OEM components. Based on your description of the problem my suspicion is the ground.

If you can get access to the actual jack motor terminals and can apply 12V power (from a suitably-rated battery known to be fully charged) and you find the jack lifts properly when directly powered in this way, then you know you have a power supply issue. New cables and new clean connections all around should take care of it.

expert reply by: Adam R

0

Walter L.

6/12/2020

My jack will not lift off my pickup hitch , unless I use my hand crank ,but the jack will come down on it's own

Reply

Chris R.

6/16/2020

I would check a couple of things here. First make sure that the battery you're hooked up to is still completely charged and in good condition. Also check that the wire connections are still secured - both the power and ground attachments. If issues still persist please let me know what model jack you have and we'll go from there.

Reply

Glenn W.

3/13/2024

@ChrisR I have this same problem on my 2004 Designer Fifth Wheel Trailer my battery is brand new sealed lead acid optima deep cell. Fuses are all good and I still have no power. How do I know if my DC side is working. When I unplug the camper from my 50amps nothing works. So it seems to me the DC side is not working at all, I have a kill switch next to the battery it on and has 12V on the out bound side.

Reply

Lazer S.

3/13/2024

@GlennW You will need to find the positive DC output wire that leads from the converter to your DC fuse block. Gently stick a tester (like # PTW2991 ) into the output port that the wire is coming from with said tester and connect the other end of the tester to your battery. The DC output should light the tester up and display the proper voltage. If it does not, then your converter is bad/malfunctioning and will typically need to be replaced.

Reply

See All (5) Replies to Walter L. ∨

Answer 1

In order to determine if the issue you are having with your landing gear legs clicking and popping is caused by the gear box or leg assembly you will simply need to disconnect the gear box from the legs and then test each manually. If you feel…

view full answer...

Answer 2

From what it looks like, the Lippert Venture Lead Leg Repair Kit for 5th Wheel RV Landing Gear #LC146059 would work on your landing gear, but without knowing the brand and capacity it's tough to confirm this. If you can find any identifying…

view full answer...

Answer 3

The skipping sound you are hearing is the motor drawing too much amperage and then "clicking" loudly as it fails to have enough amperage to move the landing gear. This is very common if the motor needs replacing or the power or…

view full answer...

Answer 4

It could be the motor but it could also be the screw/nut inside the jack leg that is causing the problem. Since you mentioned that it is hard to crank it manually I suspect that it is likely the screw and/or nut. On jacks that have an ACME screw the…

view full answer...

Answer 5

It sounds like the gearbox could be bad or possibly the motor, this could be easily confirmed by removing each of the components (gearbox/motor) and testing them separately. The gear boxes are luckily pretty standardized and not terribly expensive,…

view full answer...

Answer 6

Take the top off of the jack leg and inspect the bevel gears that you can see. If they look damaged all you'd need is the repair kit part #LC146060. If other components look damaged it would be best to replace the entire leg with part…

view full answer...

Answer 7

It sounds like you need a replacement gearbox. For a Venture replacment, that is aluminum instead of plastic, part #LC276602 is what you're looking for.

view full answer...

Answer 8

In order to pick out a direct replacement for the landing gear on your Challenger RV we would need to know the distance between the mounting brackets. Otherwise you could just have the brackets removed from your trailer by a qualified welder and then…

view full answer...

Answer 9

Most of the landing gear sets will use the same bracket height dimensions for the install of a new landing gear set. Check out the picture I attached that shows the dimensions of the brackets for the Ultra Fab landing gear for you to compare to your…

view full answer...

Answer 10

The Stromberg Carlson Electric Landing Gear Set #LG-4 will work with your 2004 5th Wheel KZ New Vision Ultra per the vendor. This system is perfect for raising, leveling, and supporting your 5th-wheel trailer or RV. The direct-drive motor will reduce…

view full answer...

Answer 11

We have exactly what you would need. For a gooseneck trailer you would need a powered landing gear set like the Ultra-Fab Deluxe Electric Landing Gear Set #UF17-943010. This dual motor set has 12,000 lbs of lifting capacity and would work very well…

view full answer...

Answer 12

Lippert made specific replacement landing gear for your 2011 Keystone Montana 5th Wheel. That means that for a replacement gear box you need the #LG-179015 and you'd be set!

view full answer...