Replacement Rubber Lube Plug For 2.44 E-Z Lube Grease Cap

Question

Question:

Can you tell me the dimensions of the hole for the plug for this easy lube 2.440 oil cap. And do you offer just a replacement plug?

asked by: Jeff

0

Expert Reply:

We have the 1.18" Rubber Lube Plug # DC-RP that fits the 2.44" Grease Cap # RG04-080.

expert reply by: Bud M

0

Answer 1

It sounds like you're looking for the E-Z Lube Grease Cap part #RG04-080 which is designed for a 2.44" hub bore. Please note, the grease cap that is designed for the hub bore is an exact figure that needs to be taken with a caliper but this…

view full answer...

Answer 2

You sure can, they're sold in pairs as part #RG04-010 or individually as part #DC-RP.

view full answer...

Answer 3

For a 5,200 lb trailer axle hub with 6 lugs the correct size dust cap/cover is 2.44 inches like the TruRyde cover part #DC250L-DCRP. Sounds like what you ordered was the version for the 8 lug hubs which is a slightly larger size.

view full answer...

Answer 4

It's hard to see the diameter of your cap in the picture you submitted but it appears you need the part #DC-RP which fits a 1.18 inch diameter hole like it looks like you have.

view full answer...

Answer 5

I do have an option for you but the Rubber Lube Plug part #DC-RP that you purchased is designed to fit a 1.18" diameter opening and will not work for you assuming the plug you measured is indeed 1.5" diameter. Instead, the better option for…

view full answer...

Answer 6

The replacement rubber caps for EZ Lube hubs are #RG04-010. These are the lube plugs for 1.18 inch dust cap holes in those EZ Lube Grease Caps. These are the equivalent of the 85-1. If you need a different size dust cap, we only have what comes with…

view full answer...

Answer 7

Based on the dimensions you listed the correct grease seal is the part #GS-2125DL. This has ID of 2.125", OD of 3.376".

view full answer...

Answer 8

To determine the correct E-Z Lube grease cap you are going to need to measure the center of the hub where the grease cap is going to fit (please see accompanying photo). The measurement will need to be very precise, so you are going to want to use a…

view full answer...

Answer 9

Trailer fuses are found in the underhood fuse block. Fuse 1 is your trailer Right stop/turn lamp. Fuse 3 is your Left stop/turn lamp. Fuse 10 is your trailer backup lamps. Fuse 25 is your trailer park lamps. If you don't want to pull the fuses,…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Replacement Rubber Lube Plug For 2.44 E-Z Lube Grease Cap

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching