Replacement Grease Seal for Seal with ID of 2.125 and OD of 3.371

Question

Question:

Can you cross grease seal # TCM 21335TB-BX ? Thanks. 2.125 / 3.371 / 0.500. Would part # TCM21334TB work. Thanks again

asked by: Coby

0

Expert Reply:

Based on the dimensions you listed the correct grease seal is the part # GS-2125DL. This has ID of 2.125", OD of 3.376".

expert reply by: Jameson C

0

Answer 1

You can verify that the 10-19 grease seal included in Bearing Kit #BK2-100 is the correct one for your spindles by taking two measurements. First you want to measure the rear hub bore where the seal is inserted. The seal's outer diameter…

view full answer...

Answer 2

We do not have a seal that matches the inner and outer diameter you have provided. That being said, I believe the markings on the seal actually indicate that your ID is 1.25" and our OD is 1.979". Your measurements are incredibly…

view full answer...

Answer 3

The seal you would want is the part #GS-2125DL. It has an outer diameter of 3.376 inches and an inner diameter of 2.125 inches.

view full answer...

Answer 4

From the numbers you provided it sounds like you need replacement grease seals. In my research, the grease seals I found with the GS-1719DL number have a 1.72 inside diameter and 2.565 outside diameter. The replacement double lip grease seals you…

view full answer...

Answer 5

Grease seal set #RG06-050 is what you will need. These are double lip seals, just like what you have (the spring indicates that) and the dimensions are all the same including the 1/2 inch width.

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

I'm sure we have a bearing kit for your trailer, though we don't have any way of knowing or cross-referencing VINs to determine what you need. So in order to find the correct kit you will need to take apart your current hub assembly and look…

view full answer...

Answer 8

The ALKO 4,400 lb axles use the same bearing sizes as the standard 3,500 lb alxes. If you want USA made bearings, I recommend the Bearing Kit #TMK52VR. This kit comes with the Timken brand bearings which are all made here in the USA.

view full answer...

Answer 9

So from what I can gather, the E3 error code on your Furrion Electric RV Fireplace with Logs #F30SW15ABL is an "overheat protection" error which explains why it only runs for a bit before shutting off. I'd recommend inspecting the…

view full answer...

Answer 10

The only difference between the #RG06-050 and Timken #TMK58ZR is the brand and quantity. Timken is typically considered to be a high quality brand, particularly for their USA made bearings. The #RG06-050 comes with two seals so it is the better…

view full answer...

Answer 11

We have the 1.18" Rubber Lube Plug #DC-RP that fits the 2.44" Grease Cap #RG04-080.

view full answer...

Answer 12

To determine the correct E-Z Lube grease cap you are going to need to measure the center of the hub where the grease cap is going to fit (please see accompanying photo). The measurement will need to be very precise, so you are going to want to use a…

view full answer...

Replacement Grease Seal for Seal with ID of 2.125 and OD of 3.371

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching