How Tall is the Timbren TFRTT1504E Kit w/ the 1" Spacer?

Question

Question:

what is the total length of the unti when you use the 1 inch spacer?

asked by: Jim A

1

Helpful Expert Reply:

The Timbren Suspension Enhancement System item # TFRTT1504E has a total height of 6.75” with a 1” spacer. This system is confirmed to fit your 2015 Ford F-150. I have linked an installation video below.

expert reply by: Jerred H

1

Answer 1

Both of the kits you mentioned are a fit for your 2016 Ford F-150. The difference is that the part #TFR1504E has a 6,000 lb capacity and the part #TFRTT1504E has a 7,000 lb capacity. You would want to go with the lower rated spring as it will be a…

view full answer...

Answer 2

While the Timbren Rear Suspension Enhancement System #TFR1504E may be able to technically fit without using the spacer, it will likely not offer you the best performance. It is supposed to be pretty tight and without the use of the spacer, the…

view full answer...

Answer 3

The Timbren Suspension Enhancement System - Rear Axle #TFRTT1504E once the brackets are installed on the top and bottom and with the integrated spacer will give you 1-1/2 inch of clearance between the jounce spring and bracket compared to the 4-1/2…

view full answer...

Answer 4

The Timbren Suspension Enhancement System #TFRTT1504E is a confirmed fit for your truck. With a 1,100 lb tongue weight trailer, this system will help to keep the rear end from squat and your headlights from being too high to see the road as…

view full answer...

Answer 5

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...