Bearing Kit For Lippert 3,500 lb Axle

Question

Question:

Looking for the corrct part numbers for wheel bearing kits and break plates for my trailer. Also thinking of converting to wet bolts for the spring hangers. The axle is a Lippert Part # 144953. 3000LB GAWR LCI35-SB-86.5-68.5-NOSP-US-L-545-7242-18PT 2013 Dutchman Kodiak travel trailer. Thank You

asked by: Peter D

0

Expert Reply:

The "LCI35" indicates that your Lippert axle uses 3,500 lb bearings and seals, and the correct bearing kit is the following:

- Hub Bearing Kit for Lippert, Dexter, and Al-Ko Axles # BK2-100

Then for wet bolts you can use the Wet Equalizer Bolt with Locknut and Grease Zerk for Double-Eye Springs # 126B2.

expert reply by: Kyle S

0

Answer 1

It really shouldn't matter what direction the wet bolts part #126B2 install when used for equalizers or shackle straps. But if Dexter says to install them in the orientation you described then I would recommend you stick with their…

view full answer...

Answer 2

While we don't have a kit with the parts you need that have those measurements, we can easily piece it together. You will just need the following: - Straight Equalizer for 1-3/4" Double-Eye Springs - 5-1/2" Long - 9/16" Center Hole…

view full answer...

Answer 3

On the wet equalizer bolt #126B2 it does not matter which way the hole faces. Up, down, left, right, anywhere in between, it's all good. A lock nut has mismatched threads a little ways along the thread spiral and either its threads, the bolts…

view full answer...

Answer 4

The standard wet bolt for trailer suspension would be the part #126B2 which is 3-5/16 inches long and 9/16 inch in diameter.

view full answer...

Answer 5

I spoke to my contact at Lippert Components Incorporated (LCI) about the Equa-Flex Cushioned Equalizers that you have on your trailer. They informed me that the equalizer does not need to be greased regularly though it would not hurt to spray a bit…

view full answer...

Answer 6

You will need to use the Wet Equalizer Bolt with Locknut and Grease Zerk for Double-Eye Springs - 3" Long #126B2. Replacement bolts for the #MR46ZR are not available so this is the only option.

view full answer...

Answer 7

Since your batteries are wired so that the two 6 volt batteries are in series and produce an output of 12 volts the part #329-GENIUS5 would be a great option. If you want to charge the batteries individually or if you want the total output to remain…

view full answer...

Answer 8

There are two ways to wire up two batteries. One way doubles the volts of the two batteries and the other keeps the same amount of volts. In parallel the voltage stays the same and in series it is doubled. Check out the diagram for more info.

view full answer...

Answer 9

In order to charge your batteries wired in parallel with the NoCo Genius #329-GENIUS5 you'll want to connect the positive charge line to the positive terminal of the first battery and the negative line to the negative terminal of the opposite…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Bearing Kit For Lippert 3,500 lb Axle

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching