Replacement Bolt for MORryde Suspension Upgrade Kit for Tandem Axle Trailers

Question

Question:

I installed a MR46ZR this weekend. I got a bot zelles on one bolt and striped the threads. It was one of the 9/16 x27/8 bolts in the kit. Is there a replacement bolt for the one in the kit or should I use the 126BZ bolt? Thank You

asked by: Peter D

0

Expert Reply:

You will need to use the Wet Equalizer Bolt with Locknut and Grease Zerk for Double-Eye Springs - 3" Long # 126B2. Replacement bolts for the # MR46ZR are not available so this is the only option.

expert reply by: Robin H

0

Answer 1

The term, wet, in this case means that the head of the bolt has a grease Zerk in it and there is a channel that leads to center of the bolt. This makes it easy to grease the bolt while installed, as you can put a grease gun right up to the Zerk and…

view full answer...

Answer 2

The "LCI35" indicates that your Lippert axle uses 3,500 lb bearings and seals, and the correct bearing kit is the following: - Hub Bearing Kit for Lippert, Dexter, and Al-Ko Axles #BK2-100 Then for wet bolts you can use the Wet…

view full answer...

Answer 3

The suspension bolts should be 9/16" diameter as these are fairly standardized so if that's what you have I recommend the Wet Equalizer Bolt part #126B2.

view full answer...

Answer 4

It really just depends on what you are looking to get out of the bushings. Bronze bushings, like part #K71-291-00, will last longer but are more noisy and it is recommended to use wet bolts like part #126B2 to keep them lubricated. Nylon bushings,…

view full answer...

Answer 5

I would be happy to help you find the correct replacement leaf spring mounting bolts for your 2020 Forest River Wildwood Heritage Glen 22RBHL Travel Trailer but unfortunately we do not have a break down of the components used on a specific trailer.…

view full answer...

Answer 6

Most trailer leaf springs will have a bushing in the eyes of the spring. It is interesting that the install video we have for the wet bolt part #126B2 that you referenced does not have a bushing involved at all. In reality all that really matters is…

view full answer...

Answer 7

Equalizer bolts, like the Redline Wet Equalizer Bolt with locknut and grease zerk, #126B2, should be torqued to yield. Equalizer bolts are not given a specific torque rating because they should allow some movement of the equalizer. If they are…

view full answer...

Answer 8

The Dexter equalizer's that you have on your trailer are 5 3/4 inches long. An upgrade equalizer kit that would work for your setup is the Equa-Flex Cushioned Equalizers - Double Eye Springs #LC279687. Since you mentioned that you are currently…

view full answer...

Answer 9

All of the tandem axle hanger kits for double-eye springs use 2-5/8 inch or 2-1/4 inch long shackle straps. The length is taken from the center of one eye to the center of the other eye. The overall length of a 2-5/8 model is just under 3-1/2 inches.…

view full answer...

Answer 10

Thank you for providing a photo of your trailer shackle straps showing the extra non-threaded portion of the Redline zerk-fitted bolts #126B2. Shackle bolts are intended to have a fairly loose fit with the shackle straps when installed properly. This…

view full answer...

Answer 11

What you'd want is the replacement suspension bolt part #166079. This is 9/16 inch in diameter like you need and is 3-1/2 inches long too. It comes with matching nut as well.

view full answer...

Answer 12

It really shouldn't matter what direction the wet bolts part #126B2 install when used for equalizers or shackle straps. But if Dexter says to install them in the orientation you described then I would recommend you stick with their…

view full answer...

Replacement Bolt for MORryde Suspension Upgrade Kit for Tandem Axle Trailers

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching