Availability of Front Trailer Hitch Receiver for 2006 Chevy Silverado 1500 Work Truck

Question

Question:

Need a 2 front mount hitch for a 2006 Chevy 1500 Silverado WORK TRUCK. Can you help me find one?

asked by: Michael R

1

Helpful Expert Reply:

The Curt Front Mount Trailer Hitch Receiver # 31302 will fit your 2006 Chevy Silverado 1500 Work Truck. I spoke with my contact at Curt to confirm this information. This hitch has a 2" receiver and a bolt on installation. It features a 9,000 lb line pull, 500 lb vertical load limit, and 5,000 lb gross trailer weight. It also comes with a limited lifetime warranty.

expert reply by: Robin H

1

Answer 1

After some research, I have found the Curt Front Mount Receiver #31302 is the only such trailer hitch we carry for your 2002 Chevrolet Avalanche. It has a line pull capacity of 9000 lbs, a vertical load of 500 lbs, and a gross trailer weight of 5000…

view full answer...

Answer 2

The front mount trailer hitch that I recommend for a 2000 Chevrolet Silverado 1500 is the Curt Front Mount Trailer Hitch Receiver part #31302. It's a direct, custom bolt-on option with no drilling required. It has a hidden crosstube design as…

view full answer...

Answer 3

The #K2AVAL8422 K2 plow attaches to the vehicle using a standard front mounted hitch. The hitch you need will depend on whether your Silverado is a 1500 or a 1500 HD model. The easy way to differentiate between the two is the hubs. The 1500 has 6…

view full answer...

Answer 4

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 5

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

Sounds like you are looking for a hitch mounted cargo carrier to mount in a front hitch for your truck. The most popular cargo carrier we have is the etrailer #e98874 which will fit a 2 inch hitch and can fold up when not needed. Being able to fold…

view full answer...

Answer 8

The install of the Curt front hitch part #31302 that fits your 2003 Chevy Silverado 1500 Z71 does not require the permanent removal of the tow hooks.

view full answer...

Answer 9

If you were to install the Curt #31302 Front Mount Hitch so that it is the "through bumper" instead of "under bumper" configuration you will need to cut out a 3 inch square hole that is located 3-1/2 inches below the top edge of…

view full answer...

Answer 10

For a through-fascia installation, the instructions state that the top of the 3 inch square hole would fall 3-1/2 inches below the top edge of the plastic fascia. Before cutting, I would strongly recommend you confirm these measurements for yourself.…

view full answer...

Answer 11

For your 2004 Chevrolet 1500 HD you want front hitch #65028.

view full answer...

Answer 12

A great style of bike rack for front hitches is the platform style. This will increase visibility when driving. A great bike rack for this is the Thule T2 Classic 2 Bike Platform Rack #TH9045, its is a great fit with your trailer hitch #65003. Most…

view full answer...