Recommended Front Mount Hitch for a 2000 Chevy Silverado 1500

Question

Question:

What front mount hitch will fit 2000 chevy silverado 1500

asked by: Everette S

1

Helpful Expert Reply:

The front mount trailer hitch that I recommend for a 2000 Chevrolet Silverado 1500 is the Curt Front Mount Trailer Hitch Receiver part # 31302. It's a direct, custom bolt-on option with no drilling required. It has a hidden crosstube design as well so all you'll see is the receiver tube opening.

expert reply by: Conner L

1

Answer 1

After some research, I have found the Curt Front Mount Receiver #31302 is the only such trailer hitch we carry for your 2002 Chevrolet Avalanche. It has a line pull capacity of 9000 lbs, a vertical load of 500 lbs, and a gross trailer weight of 5000…

view full answer...

Answer 2

The Curt Front Mount Trailer Hitch Receiver #31302 will fit your 2006 Chevy Silverado 1500 Work Truck. I spoke with my contact at Curt to confirm this information. This hitch has a 2" receiver and a bolt on installation. It features a 9,000 lb…

view full answer...

Answer 3

The #K2AVAL8422 K2 plow attaches to the vehicle using a standard front mounted hitch. The hitch you need will depend on whether your Silverado is a 1500 or a 1500 HD model. The easy way to differentiate between the two is the hubs. The 1500 has 6…

view full answer...

Answer 4

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 5

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 6

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 7

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

While trailer axles do feature an upward bend like you are describing, there isn't a particular amount/measurement that is standard across the board. This bend in the axle is designed so that it will straighten under a trailer's loaded…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

The B&W Companion OEM 5th Wheel Trailer Hitch #BWRVK3700 is perfectly compatible with cushioned pin boxes like your MORryde RP072-1621HD, so the clunking you're experiencing isn't related to the two components being incompatible. With…

view full answer...

Answer 12

It's totally normal for a bit of movement between any fifth wheel hitch and the base rails. The feet on the hitch are typically a bit smaller than the slots they slide into for mounting otherwise you'd have a hard time getting your hitch in…

view full answer...

Recommended Front Mount Hitch for a 2000 Chevy Silverado 1500

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching