Replacement Actuator Solution for Tie Down 70LC

Question

Question:

I’m looking an 04 brake actuator to a nitro boat trailer The factory model is a 70LC but when I look it up I can’t find anything for it. If I can get the factory or a replacement part it would be appreciated

asked by: Gavin G

0

Expert Reply:

The Tie Down 70LC drum brake actuator is rated for 7,000 lbs and attaches to a 2" trailer hitch ball so for a similar actuator you'd want the part Titan Zinc-Plated Brake Actuator # T43397007K.

expert reply by: Jameson C

0

Answer 1

According to my research the Tie Down 70lc is a hydraulic disc brake actuator. They are no longer made but can definitely be replaced with another actuator. I recommend to use the Dexter DX7.5 Drop-N-Go Brake Actuator - Disc Brakes part #099-175-20…

view full answer...

Answer 2

We have exactly what you are looking for. Based on my research your Tie Down 70LC has a 7000lb rating and uses a 2" hitch ball. If your trailer has drum brakes I recommend the Titan Zinc-Plated Brake Actuator - Drum - Multi-Fit Ball - Bolt On -…

view full answer...

Answer 3

According to my research, the Tie Down 70LC drum brake actuator is rated for 7,000 lbs and attaches to a 2" trailer hitch ball, and we do have a quality replacement for that from Titan: - Titan Zinc-Plated Brake Actuator #T43397007K This…

view full answer...

Answer 4

The Dexter Actuator Inner Member part #DX99FR is designed as a replacement center section for the Dexter DX7.5L A-60 part #DX56FR which was designed to fit a 3 inch wide by 5 inch tall straight trailer tongue. If you are looking for a coupler…

view full answer...

Answer 5

The main difference between The Dexter Inner Membrane #DX99FR and The Dexter inner Membrane #DX39FR is that the #DX99FR is for a tandem axle with disc brake setup. The #DX39FR is for a single axle with disc brake setup. Both Dexter membranes have a 2…

view full answer...

Answer 6

There isn't a set dimension for that on trailers. Typically axles are custom ordered to the specs needed. They order the spring seat to seat dimension for mounting to the trailer and then the hub face to face dimension for what will clear the…

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 9

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Your surge coupler will have either a sticker or an engraving on it, typically near where the coupler is located. If you can get me that information and what you're needing to replace on it I'd be more than happy to help you find what…

view full answer...

Answer 12

Yes, you can weld on the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout - Bolt On - Disc - 2" Ball - Zinc - 7.5K item #DX56FR you referenced. You will want to make sure you remove the zinc coating and get down to the bare metal. I have…

view full answer...